Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
Ed

Criado por

Ed

9. novembro 2026FI
10
0
0
0
0

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)

A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel. A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring. Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
Avançado
Unknown

Instruções

1

Read Hug

"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2

Build the stirrer base

Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.

Materiais para este passo:

Chapa de alumínioChapa de alumínio1 housing
Motor elétricoMotor elétrico1 peça
Conjunto de ímanes de barraConjunto de ímanes de barra1 drive magnet
ReóstatoReóstato1 peça
Cabo flexível com fichaCabo flexível com ficha1 peça

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
Método de conformação desconhecidoMétodo de conformação desconhecido
3

Make the radiation shield

Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.

Materiais para este passo:

Chapa de aço inoxidável - 304Chapa de aço inoxidável - 3041 shield and legs
Varão roscadoVarão roscado1 spindle
Porca sextavadaPorca sextavada2 peças

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Método de conformação desconhecidoMétodo de conformação desconhecido
4

Fit the relay magnet

Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.

Materiais para este passo:

Conjunto de ímanes de barraConjunto de ímanes de barra1 relay magnet, 1/4 x 1 x 1 3/4 in.
Material desconhecidoMaterial desconhecido1 hub and strap
Parafusos de máquinaParafusos de máquina2 peças

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
5

Mount the supports

Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.

Materiais para este passo:

Chapa de aço inoxidável - 304Chapa de aço inoxidável - 3041 three supports
Parafusos de máquinaParafusos de máquina3 peças
Material isolante desconhecidoMaterial isolante desconhecido3 tubular spacers

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
6

Fit the heater and top

Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.

Materiais para este passo:

Elemento de aquecimentoElemento de aquecimento1 ring heater
Cabo flexível com fichaCabo flexível com ficha1 peça
Porca sextavadaPorca sextavada2 peças
Chapa de alumínioChapa de alumínio1 heat sink
Chapa de alumínioChapa de alumínio1 top plate
Parafusos de máquinaParafusos de máquina3 peças

Ferramentas necessárias:

Ferramenta de repuxagemFerramenta de repuxagem
Torno mecânicoTorno mecânico
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas

Materiais

13

Ferramentas necessárias

8

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...