Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)
A workshop compressor driven by a 1 hp electric motor: an old single-cylinder motorcycle engine rebored and run as a pump, its exhaust port blanked, its own automatic inlet valve taking in air, and a ball check valve in the spark-plug hole sending air to a tank.
Source: Popular Mechanics Shop Notes for 1919, pp. 3166-3167. Unknown: tank, belt and sizes. Picture: the article's drawing.
Intermediário
Unknown
Instruções
1
1
Recondition the cylinder
Recondition the cylinder
Rebore the old engine and fit a new piston for good compression. Remove the exhaust valve and bolt a steel plate, with a gasket under it, over the exhaust port. Leave the automatic inlet valve as it is: it now draws in air.
Materiais para este passo:
Material desconhecido1 old motorcycle engine
Conjunto de pistão e biela1 new piston
Chapa grossa de aço macio1 blanking plate
Junta de vedação1 peça
Parafuso de cabeça hexagonal - classe 8.81 peçaFerramentas necessárias:
Barra de mandrilar
Torno mecânico
Berbequim de mão
Chave inglesa ajustável2
2
Fit the outlet
Fit the outlet
In place of the priming cock on top of the cylinder (the drawing shows it screwed into the spark-plug hole) fit a ball-valve hose connection, and run its hose to the air tank.
Materiais para este passo:
Válvula de retenção de esfera1 peça
Mangueira de ar comprimido1 peça
Material desconhecido1 air tankFerramentas necessárias:
Chave inglesa ajustável3
3
Fit the drive and mount it
Fit the drive and mount it
Fit a longer main shaft and key an ordinary shaft pulley on its end. Leave the old flywheel in place for momentum. Bolt steel lugs to the floor and fasten the engine base to them. Belt it to a 1 hp, 110 volt motor, and put oil in the crankcase for splash lubrication.
Materiais para este passo:
Varão de aço macio1 longer main shaft
Roldana1 peça
Chapa grossa de aço macio1 floor lugs
Parafuso de cabeça hexagonal - classe 8.81 peça
Motor elétrico1 1 hp, 110 V
Óleo de máquina1 peçaFerramentas necessárias:
Torno mecânico
Chave inglesa ajustávelMateriais
11- 1 air tankReferência
- 1 new pistonReferência
- 1 floor lugsReferência
- 1 peçaReferência
- Referência
- Referência
- Referência
- 1 longer main shaftReferência
- 1 peçaReferência
- 1 1 hp, 110 VReferência
- 1 peçaReferência
Ferramentas necessárias
4- Referência
- Referência
- Referência
- Referência
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
