Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Toothed-Disk Pass Churn: Cream Poured In Passes Once Between Fixed Toothed Disks and a Toothed Wheel Spinning Between Them
Buttercup

Criado por

Buttercup

11. novembro 2026IE
8
0
0
0
0

Toothed-Disk Pass Churn: Cream Poured In Passes Once Between Fixed Toothed Disks and a Toothed Wheel Spinning Between Them

William Jackson and Joseph Clarke of Syracuse, New York, received US 32,250, dated 7 May 1861, for a churn with two fixed disks clamped together near its top and a wheel spinning between them, all three faced with concentric rows of teeth that run between each other. With the wheel turning fast, cream poured into a cup on top passes in near the centre, out between the wheel and the upper disk, back in under the wheel, and drops through holes in the lower disk to beaters below. They found one pass through the teeth enough to churn it. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

One pass through the teeth

A carregar o notebook Jupyter…
2

Cream poured between a fixed and a turning face, five months before

Pike pours cream between two ribbed dishes. Jackson and Clarke send it through a wheel between two disks, all toothed, in a single pass.
3

Read US 32,250

"The tendency of the wheel while in rapid motion is to prevent the too free flow of the milk through the disks, and by retaining it between the disks until it has had the effect of a number of revolutions of the wheel, the butter globules are all broken ... It has been found that the great amount of friction in the passage of the cream through the disks caused by the teeth, is sufficient to churn it thoroughly in being once passed through."
4

Print the socket F

The socket on the bucket's floor: 40 mm across, 12 high, with a 16.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
5

Print the lower disk B

The lower disk: 216 mm across, 6 thick, with a rim 32 high and two rows of 6 mm teeth 12 high at 40 and 70 mm out on its upper face, a 18 mm centre hole and four 10 mm openings R at 25 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
6

Print the wheel C

The centre wheel: 192 mm across, 6 thick, two rows of teeth at 55 and 85 mm on each face (12 high below, 10 above), a hub 28 across and a 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
7

Print the upper disk A and cup G

The upper disk: 216 mm across, 6 thick, two rows of teeth 10 high at 40 and 70 mm on its underside, the cup G 146 across and 30 high on top, a 18 mm centre hole and four 10 mm openings P at 25 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
8

Body, ring, disk pack and shaft E

Use a 20-litre food-grade bucket and set the socket F in the middle of its floor. Cut a 6 mm HDPE ring 200 mm across inside and pressed down until it wedges in the bucket's taper about 244 mm up. Cut a 16 mm stainless shaft E 425 mm long. Screw two hardwood beaters T 240 x 30 x 8 mm, tilted 20 degrees, on hardwood hubs pinned to the shaft 60 and 150 mm above its foot, a quarter turn apart. Stand the shaft in the socket, slide the disk B down it onto the ring, then the wheel C, pinned on the shaft 14 mm above B's face, then the disk A on B's rim, and screw A to the rim through four holes so they are closed tightly together.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Filamento PETGFilamento PETG1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira8 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
BússolaBússola
Serra tico-ticoSerra tico-tico
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
9

Print the cog wheel H

The cog wheel on the shaft's top: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
10

Print the wheel I

The driving wheel: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls; needs a 220 mm bed.
Arquivo de designSTLCC0 - Free
11

Cover L, conductor O, standard K, wheels H and I, crank J

Cut a 12 mm HDPE cover L to the bucket's top, bored 16.8 mm at the centre for the shaft and 12.6 mm 55 mm off it, over the cup, for the conductor O: a 12 mm stainless tube 100 mm long with a small kitchen funnel on top. Pin the cog wheel H on the shaft 40 mm above the cover. Screw two hardwood bearing blocks 50 x 25 x 118 mm to the cover 60 and 125 mm in front of the centre, bored 16.6 mm across 93 mm up, run a 16 mm stainless shaft 150 mm long through them with the wheel I pinned on its inner end meshing H, a shaft collar, and a crank J of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiais para este passo:

Chapa de PEADChapa de PEAD1 peça
Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Funil de cozinhaFunil de cozinha1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Shaft CollarShaft Collar1 peça
ContrapinoContrapino3 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira6 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
12

The build in 3D

FreeCAD model of this build, cut open: the socket, the shaft with its two beaters, the ring in the bucket's taper carrying the disk pack (lower disk with its rim, the toothed wheel, the upper disk with its cup), the cover with the conductor and funnel, and the gearing and crank.
Arquivo de designBLENDCC0 - Free
13

Churn in one pass

Turn the crank briskly first, so the wheel spins, then pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, slowly into the funnel, timing it. Keep turning while it runs through the disks into the bucket below, and on a little with the beaters so the butter gathers. Lift off the cover and the disk pack, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it. Take the pack apart to wash it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
14

Troubleshooting

Toothed-disk churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Wm. Jackson** and **Joseph Clarke** of Syracuse, Onondaga County, New York, US 32,250, 7 May 1861, "Churn". They claimed "the employment of the disks A. and B. with their concentric rows of teeth, as specified in combination with the central wheel C", and wrote that one pass churns the cream thoroughly; we have not tested that. Their teeth were pyramids; ours are square pegs. They do not say how the disk pack is held; ours sits on a ring wedged in the bucket's taper. Their wheels H and I were bevel gears; ours are a printed pinion and crown wheel. The patent gives no sizes; every size here is ours.

Materiais

16

Ferramentas necessárias

15

Ficheiros de design

7

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...