Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Water-Jacket Revolving Box Churn: A Box With No Dasher Turns on Stub Axles Inside Warm or Cold Water
Martin

Criado por

Martin

9. novembro 2026NO
3
0
0
0
0

Water-Jacket Revolving Box Churn: A Box With No Dasher Turns on Stub Axles Inside Warm or Cold Water

Jeremiah Mitchell of Gasport, New York, received US 23,186, dated 8 March 1859, for a churn with no paddles or dashers: a square-cornered box turned end over end on stub axles that do not pass through it. Its lining is surrounded by a water space, filled warm or cold and checked with a thermometer. The cream goes in through a door held by buttons, the buttermilk comes out of a tap, and a pin through one standard into a ring of holes holds the box still. This rung builds it with two nested food containers in a plywood box on timber standards.
Intermediário
About 8 hours

Instruções

1

Water space and weight

A carregar o notebook Jupyter…
2

Warming or cooling the cream, before it

Stafford stood his churn in warm or cold water. Mitchell builds the water round the lining and drops the dasher.
3

Read US 23,186

"The nature of my invention consists in the employment of a revolving box, partially surrounded by a warm or cold water jacket, into which the cream is introduced, and butter made expeditiously without the use of the paddles or dashers as in ordinary churns."
4

Print the spacer

A block that holds the lining off the jacket's floor. Print four. PETG, 0.2 mm layers, 100 % infill; wash before fitting.
Arquivo de designSTLCC0 - Free
5

Lining and water space

Use two food-grade containers with rims: a lining 300 x 200 x 220 mm outside, with its snap-on lid, and a jacket 380 x 280 x 260 mm outside. Stand the lining on the four spacers in the jacket so their rims are level and the gap is 37 mm all round. Drill a 19 mm hole in the jacket's end low down for the brass spigot and a 7 mm hole in the other end for the thermometer probe, and drill the lining's lid for the PVC spigot n.

Materiais para este passo:

Recipiente de armazenamento de grau alimentarRecipiente de armazenamento de grau alimentar2 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Fita métricaFita métrica
6

Box a and face L

From 18 mm plywood make box a round the jacket: a back 416 x 316 mm, two sides 380 x 260 mm and two ends 316 x 260 mm. Cut face L 416 x 316 mm from 12 mm plywood with a 310 x 210 mm opening for the lining's rim. Bed L on silicone on both rims and screw it to the box, so the water space is sealed and only the lining opens. Screw two hardwood turn buttons r on L to hold the lid (door h) down. Fit the brass spigot through the box end into the water space and the PVC spigot through the lid, each sealed with silicone, and push the thermometer probe through its hole in silicone.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira40 peças
Vedante de siliconeVedante de silicone1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Torneira de latãoTorneira de latão1 peça
Torneira de PVCTorneira de PVC1 peça

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Conjunto de serras-copoConjunto de serras-copo
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
GramposGrampos
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
7

Axles, standards and crank

Screw a hardwood hub 100 x 100 x 30 mm to the middle of each end, bore it 30 mm and cross-bolt a 30 mm steel stub axle in it; the axles do not pass through the box. Drill twelve 10.5 mm holes e in a circle 80 mm out from the axle on one end. Stand two 70 mm posts 500 mm to the axle line on 600 mm feet, 540 mm apart, joined by a low rail, and bolt a flange bearing on each post's outer face. Drill the post on the holes' side for pin p, a 10 mm dowel. Fix a hardwood crank arm 270 mm long on the other axle and glue in a 28 mm dowel handle.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Veio de aço de 30 mmVeio de aço de 30 mm1 peça
Jogo de parafusos hexagonais M10Jogo de parafusos hexagonais M103 peças
Madeira macia de 70x70 mmMadeira macia de 70x70 mm4 peças
Parafuso para madeira n.º 10 x 3"Parafuso para madeira n.º 10 x 3"16 peças
Mancal de flangeMancal de flange2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Chave inglesa ajustávelChave inglesa ajustável
Fita métricaFita métrica
8

The build in 3D

FreeCAD model of this build, the near half of the box cut away: the lining on its spacers in the jacket, box a with face L, door h, buttons and spigots, the stub axles in their hubs, the standards with flange bearings, pin p and the crank.
Arquivo de designBLENDCC0 - Free
9

Churn

Pin the box still, face L up. Fill the water space through the brass spigot with warm water in cold weather or ice water in warm weather, watching the thermometer, until the probe reads about 15 °C. Open the door and pour in about 8 litres of heavy cream, then snap the lid on and turn the buttons over it. Pull the pin and turn the crank steadily; time it. When the butter has come, pin the box face up, draw off the buttermilk through spigot n, open the door, lift the butter out, wash it in cold water until the water runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
ÁguaÁgua1 peça
Gelo picadoGelo picado2 kg
Sal marinho grossoSal marinho grosso1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Water-jacket churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Jeremiah Mitchell** of Gasport, Niagara County, New York, US 23,186, 8 March 1859, "Churn". He held his churn simple, quick to clean for want of dashers, and tight, spattering no cream, and claimed the revolving box made and worked as described. His lining was tin and his water space ran round three faces and behind the back; ours is a food container with water on all five faces. He gave no sizes: every size and material is ours.

Materiais

19

Ferramentas necessárias

15

Ficheiros de design

2

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...