Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
Forge

Criado por

Forge

13. novembro 2026NO
5
0
0
0
0

Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)

Michael Pemmerl of Chatham, New Jersey, received US 2,518,059, dated 8 August 1950, for an industrial mallet with heads that change. A threaded stud stands out of each end of the steel head, and percussion members of different hardness screw on. A soft member is moulded round a hard ferrule with flanges and a threaded bore, so it cannot pull off. A steel cup holds its inner end from bulging. A thick rubber washer between cup and head stops it working loose and soaks up the shock before it reaches the hand. We make two rubber members from rubber sheet bonded round a flanged nut. The sizes are ours.
Intermediário
About 2 days

Instruções

1

Building a rubber member round its ferrule

A carregar o notebook Jupyter…
2

Read US 2,518,059

"The frictional and cushioning washers 16 and 23, as interposed between the respective percussion members 14 and 17 and the mallet head 10, serve the two-fold purpose of setting up a strong frictional resistance against tendency of said percussion members to accidentally loosen or turn off the coupling studs 13 when the mallet is in use, while at the same time said washers act as impact shock absorbing means."
3

Turn the head 10

From 35 mm steel round bar turn a head 90 mm long between its end faces, and at each end a stud 13 12 mm across and 20 mm long; cut an M12 thread on each with the die. Drill a 20 mm eye through the middle, square to the axis, in a V-block, for the handle.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 peça
Óleo de corteÓleo de corte1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Jogo de machos e cossinetesJogo de machos e cossinetes
Porta-cossinetePorta-cossinete
Torno de bancadaTorno de bancada
Engenho de furarEngenho de furar
Bloco em VBloco em V
Jogo de brocasJogo de brocas
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Óculos de segurançaÓculos de segurança
4

Ferrules 18 and cups 21-22

For each member, saw an M12 coupling nut to 30 mm and lock a 24 mm washer on it 4 mm from each end with a nut and thread locker: the flanges 19 round the threaded bore 20. Turn two cups from 45 mm bar: a base 3 mm thick with a 13 mm hole, and a skirt 12 mm deep bored 40.5 mm to embrace the member's inner end.

Materiais para este passo:

Porca sextavadaPorca sextavada6 peças
Anilha planaAnilha plana4 peças
Travador de roscasTravador de roscas1 peça
Barra redonda de aço macioBarra redonda de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Torno de bancadaTorno de bancada
Chave inglesa ajustávelChave inglesa ajustável
Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Barra de mandrilarBarra de mandrilar
Goiva de sangrarGoiva de sangrar
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
5

Build the rubber members 17

Scribe and cut 4 mm rubber discs 40 mm across with the knife: for each member, seven holed to the ferrule (24 mm holes level with the two flanges and 22 mm round the nut, so the discs either side trap each flange's rim) and five solid discs for the striking face. Brush contact cement on both faces, let it go touch-dry, and build the member up over its ferrule, the ferrule's end flush with the member's inner end; press it in clamps overnight and trim it round.

Materiais para este passo:

Placa de borracha naturalPlaca de borracha natural1 peça
Cola de contactoCola de contacto1 peça

Ferramentas necessárias:

BússolaBússola
X-ato (faca de precisão)X-ato (faca de precisão)
Sargento de barraSargento de barra
6

Handle and assembly

Turn an ash handle 300 mm long, fit it in the eye with a glued wedge. Cut two 6 mm rubber washers 23, 40 mm across with 13 mm holes. On each stud put a rubber washer, then a cup, skirt outwards, then screw a member on until its end is in the cup and the washer is squeezed; it should take a firm twist to undo.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Placa de borracha naturalPlaca de borracha natural1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)
Serra de arco para metaisSerra de arco para metais
Martelo de bolaMartelo de bola
X-ato (faca de precisão)X-ato (faca de precisão)
7

Troubleshooting

Interchangeable-head mallet troubleshooting.

Flow

Loading...
8

History and honest limits

**Michael Pemmerl** of Chatham, New Jersey, US 2,518,059, dated 8 August 1950, filed 31 October 1947. He claimed a mallet head with a screw-threaded coupling stud at an end, "a percussion member made of relatively soft material such as lead, an internally screw-threaded ferrule made of hard metal imbedded in said percussion member, said ferrule having external annular flanges", "a perforate cupped reenforcing member", and "a perforate rubber washer of substantial thickness" between cup and head. His soft members were moulded, and he names rubber among their materials; ours are rubber discs bonded round the ferrule. He also shows hard metal and rawhide members. He gives no sizes; every size here is ours.

Materiais

9

Ferramentas necessárias

21

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...