Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
PTFE Thread Seal Tape: Paste-Extruded, Calendered, Never Sintered
English
Emma

Criado por

Emma

26. outubro 2026SE
17
0
0
0
0

PTFE Thread Seal Tape: Paste-Extruded, Calendered, Never Sintered

The white tape wound on pipe threads is PTFE that has never been melted. Fine PTFE powder is mixed with a lubricant, pressed into a slug, squeezed through a slit die by a ram, rolled thin between two rolls, and dried. Kept below the sintering heat (about 350 °C) it stays soft and conforms to the thread (process: US 5,415,939, 1995). The targets and tests are those of the Indian standard IS 14643 (from BS 4375): no fillers, at most 0.1 % lubricant left, usually 12 mm wide and 0.075 mm thick. The lubricant (naphtha) and the slitter are ours. The picture: Fig. 1a of the patent.
Avançado
1 day

Instruções

1

Wet the powder

Mix fine (dispersion-made) virgin PTFE powder with a lubricant that can be driven off completely. Granular PTFE will not paste-extrude. No fillers. Ours: naphtha, as required.

Materiais para este passo:

Pó fino de PTFEPó fino de PTFE1 batch

Ferramentas necessárias:

NaftaNafta
2

Press a preform

Compact the wet powder into a cylindrical preform in a mould with a plunger.

Ferramentas necessárias:

Molde de compressãoMolde de compressão
Prensa hidráulicaPrensa hidráulica
3

Ram-extrude a flat tape

Put the preform in the extrusion press. The plunger pushes it out through a slit die as a thick flat tape.

Ferramentas necessárias:

Prensa de extrusão hidráulicaPrensa de extrusão hidráulica
4

Calender it thin

Pass the tape between two counter-rotating rolls to a thin tape, aiming at about 0.075 mm.

Ferramentas necessárias:

LaminadorLaminador
MicrómetroMicrómetro
5

Dry off the lubricant

Dry the tape until the lubricant is gone. Keep it well below the sintering heat (about 350 °C): sintered tape is stiff and will not seal.

Ferramentas necessárias:

Estufa de secagemEstufa de secagem
6

Slit and spool

Slit it to width, usually 12 mm (±0.5 mm), and wind it on spools.

Ferramentas necessárias:

Cortadora-rebobinadoraCortadora-rebobinadora
7

Check the tape

It must look white, with no visible specks or torn edges. Measure the thickness at five points along a sample; each must be within 10 % of their mean.

Ferramentas necessárias:

MicrómetroMicrómetro
8

Test the residual lubricant

Weigh about 15 g of tape. Extract it in a Soxhlet with petroleum spirit (40-60 °C) for at least 4 h, dry it at 100 °C, then heat it at 300 °C for 6 h, cool and weigh. The loss must be 0.1 % or less.

Ferramentas necessárias:

Extrator SoxhletExtrator Soxhlet
Éter de petróleoÉter de petróleo
Estufa de secagemEstufa de secagem
Cadinho de açoCadinho de aço
Câmara de dessecação (pequena)Câmara de dessecação (pequena)
Balança digital de precisãoBalança digital de precisão
9

Wrap a thread

Wind tape round an R 1/2 taper pipe thread with 50 % overlap, two layers deep, just tight enough to take the thread form. It must hold the form, not break, and its end must stay put.

Ferramentas necessárias:

Acessório roscado para tubagemAcessório roscado para tubagem

Materiais

1

Ferramentas necessárias

14

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...