Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)
Forge

Criado por

Forge

13. novembro 2026NO
7
0
0
0
0

Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)

James H. Reinhardt of East Orange, New Jersey, received US 1,261,438, dated 2 April 1918, for a profile gauge: a row of pins clamped between two thin metal members. Rubber tubes wrapped in cloth press on the pins, so each one slides when pushed and stays where it is left. Pressed against an object, the pin ends take its outline, and a pencil drawn along them copies it, so the shape can be made again. We build his single gauge from brass sheet and steel wire. All sizes are ours.
Intermediário
About 5 hours

Instruções

1

How many pins

A carregar o notebook Jupyter…
2

Read US 1,261,438

"The rods or pins 3 of the respective gages may be pushed against the surface of the object, as required, to obtain its outline along the ends of the rods or pins, whereby a pencil may be drawn along the ends of the pins to trace such outline or contour of the object. From such outlines objects corresponding to the master object may be reproduced either in relief or concave according to which way the outline drawn from the ends of the rods is used."
3

Make the two members

Cut two strips of 0.8 mm brass sheet 200 x 32 mm (ours) with tin snips and file the edges. Bend 4 mm down along each long side in the vice, so each strip becomes a shallow channel 24 mm wide: his "gutter-like form". Clamp them together, open sides facing, and drill a 3.5 mm hole through both, 50 mm from each end, on the middle line.

Materiais para este passo:

Chapa de latãoChapa de latão2 peças

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Jogo de limasJogo de limas
Torno de bancadaTorno de bancada
Ponta de traçarPonta de traçar
Berbequim de mãoBerbequim de mão
4

Make the gutters

Cut two strips of the same brass 180 x 14 mm and bend each round a 6 mm rod into a U that will hold the rubber tube, his gutters 10. Rivet them inside one member, one near each long side, with copper rivets, keeping clear of the screw holes.

Materiais para este passo:

Chapa de latãoChapa de latão1 peça
Rebites de cobreRebites de cobre6 peças

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Varão de aço macioVarão de aço macio
Torno de bancadaTorno de bancada
Berbequim de mãoBerbequim de mão
Martelo de bolaMartelo de bola
5

Make the retainers

Cut two pieces of 6 mm rubber tubing 170 mm long and push a 2 mm wire through each, his cores 9, "to somewhat stiffen them". Wrap each in a strip of cotton cloth, lap its edges and glue them with contact cement, his protecting cloth 12, so the rubber does not touch the metal. Lay one in each gutter.

Materiais para este passo:

Tubo de borrachaTubo de borracha1 peça
Arame de açoArame de aço1 peça
Pano de algodãoPano de algodão1 peça
Cola de contactoCola de contacto1 peça

Ferramentas necessárias:

Alicate de corteAlicate de corte
TesouraTesoura
6

Cut the pins

Cut 1 mm steel wire into pins 120 mm long, as many as the notebook gives. Straighten any that are bent and file both ends flat and smooth, so they slide easily and do not mark the work.

Materiais para este passo:

Arame de açoArame de aço1 peça

Ferramentas necessárias:

Alicate de corteAlicate de corte
Jogo de limas de agulhaJogo de limas de agulha
Torno de bancadaTorno de bancada
7

Assemble

Lay the member with the retainers open side up. Lay the pins across it side by side, touching, centred so equal lengths stick out on both sides; leave a gap at each screw hole (ours). Put the other member on top and pass a machine screw through each hole with a nut. Tighten them evenly until each pin slides when pushed but does not fall.

Materiais para este passo:

Parafusos de máquinaParafusos de máquina2 peças
Porca sextavadaPorca sextavada2 peças

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Chave inglesa ajustávelChave inglesa ajustável
8

Take a profile

Push all the pins level with a flat board. Press the gauge square against the object until the pins have taken its shape. Lift it off, lay it on paper or on the stock to be cut, and draw a pencil along the pin ends.

Ferramentas necessárias:

LápisLápis
9

Troubleshooting

Pin profile gauge troubleshooting.

Flow

Loading...
10

History and honest limits

**James H. Reinhardt** of East Orange, New Jersey, US 1,261,438, dated 2 April 1918, filed 20 June 1914. He claimed "a profile gage comprising a pair of opposed members, rods or pins located between and transversely with respect to said members, means for clamping said members together" and "a resilient retainer comprising spaced rubber tubes". His members can have teeth along their edges, and his patent also covers end castings that join several gauges in a line or at an angle, a smaller gauge clamped between them, a toothed spacer strip and a rubber-mat retainer: none of those are built here. He gives no sizes: the brass, the 200 mm length, the 1 mm pins, the tube and core sizes, the cement, the rivets and the screws are ours.

Materiais

8

Ferramentas necessárias

13

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...