Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)
Tex

Criado por

Tex

13. novembro 2026FO
6
0
0
0
0

Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)

Harry Richter of Omaha received US 901,476, dated 20 October 1908, for a box with two trays under one lid: sweets below, and above them a deeper tray for a valentine, held flat by little card wings so it never touches the lid. The trays stack on an inner rim and cannot slide, and come apart easily. We make it from pasteboard and card. All sizes are ours.
Iniciante
About 3 hours

Instruções

1

Box sizes

A carregar o notebook Jupyter…
2

Read US 901,476

"The device affords a secure housing for these articles, and by reason of the formation and arrangement of parts, it may be economically constructed."
3

Make the lower tray

Cut the bottom 1 from pasteboard and glue an upturned rim 3 round it from a card strip, scored and folded at the corners. Glue a second strip inside it, his sustaining leaf 4, standing about 6 mm (ours) above the rim all round.

Materiais para este passo:

Cartão coladoCartão colado1 peça
CartolinaCartolina1 peça
ColaCola1 peça

Ferramentas necessárias:

LápisLápis
RéguaRégua
X-ato (faca de precisão)X-ato (faca de precisão)
Dobradeira de ossoDobradeira de osso
Pincel para colaPincel para cola
4

Make the upper tray

Cut the bottom 6 the same size and glue a deeper rim 8 round it. Glue an enclosing strip 9 round the outside of rim 8, a little lower than it at the top and reaching about 6 mm below the bottom (his portion 10), so the upper tray sits on the lower one with the enclosing strip round the lower tray's inner rim.

Materiais para este passo:

Cartão coladoCartão colado1 peça
CartolinaCartolina1 peça
ColaCola1 peça

Ferramentas necessárias:

RéguaRégua
X-ato (faca de precisão)X-ato (faca de precisão)
Dobradeira de ossoDobradeira de osso
Pincel para colaPincel para cola
5

Make the card wings

Cut two small triangular card wings, each with a folded flange 16. Glue the flanges inside rim 8, midway between the ends, one each side, so the wings can be bent down over the bottom: their lower edges 17 press on the valentine and keep it off the lid.

Materiais para este passo:

CartolinaCartolina1 peça
ColaCola1 peça

Ferramentas necessárias:

X-ato (faca de precisão)X-ato (faca de precisão)
Dobradeira de ossoDobradeira de osso
Pincel para colaPincel para cola
6

Make the lid

Cut the top leaf 11 to fit over the upper tray and glue a rim 13 round it, sized so it rests on the enclosing strip 9, as his Fig. 4.

Materiais para este passo:

Cartão coladoCartão colado1 peça
CartolinaCartolina1 peça
ColaCola1 peça

Ferramentas necessárias:

RéguaRégua
X-ato (faca de precisão)X-ato (faca de precisão)
Dobradeira de ossoDobradeira de osso
Pincel para colaPincel para cola
7

Fill and close it

Put the sweets in the lower tray, set the upper tray on it, lay the valentine in and bend the wings down over it, and put the lid on. Lift the upper tray off to reach the sweets.
8

Troubleshooting

Valentine box troubleshooting.

Flow

Loading...
9

History and honest limits

**Harry Richter** of Omaha, US 901,476, dated 20 October 1908, filed 29 November 1907. He claimed a box with a lower receptacle with an inner sustaining rim, an upper receptacle with an outer enclosing rim, "flexible holding-wings having flanges secured upon the inner sides of the integral upturned rim", and a cover. He made the wings "preferably of card board" and gives no sizes: the pasteboard, all sizes and glue are ours.

Materiais

3

Ferramentas necessárias

5

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...