Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

Criado por

Forge

26. outubro 2026NO
24
0
0
0
0

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
Iniciante
30 minutes

Instruções

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

Materiais para este passo:

Arame de ferroArame de ferro1 peça

Ferramentas necessárias:

RéguaRégua
Alicate de corteAlicate de corte
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

Ferramentas necessárias:

Jogo de limas de agulhaJogo de limas de agulha
Torno de bancadaTorno de bancada
3

Point the screw end

File that end to a tapering point (Fig. 3).

Ferramentas necessárias:

Lima para metalLima para metal
Torno de bancadaTorno de bancada
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

Ferramentas necessárias:

Porta-cossinetePorta-cossinete
Torno de bancadaTorno de bancada
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

Ferramentas necessárias:

Alicate de bicos redondosAlicate de bicos redondos
Alicate de bico chatoAlicate de bico chato
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

Materiais para este passo:

Arame de ferroArame de ferro1 peça

Ferramentas necessárias:

Alicate de corteAlicate de corte
Alicate de bicos redondosAlicate de bicos redondos
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

Ferramentas necessárias:

Alicate de bico chatoAlicate de bico chato
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

Materiais

1

Ferramentas necessárias

8

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...