Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
Charlie

Criado por

Charlie

9. novembro 2026DE
10
0
0
0
0

Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)

A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock. The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap. Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
Avançado
Unknown

Instruções

1

Read Demers

"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2

Blow the vessel

Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.

Materiais para este passo:

Vidro desconhecidoVidro desconhecido1 vessel

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
Método de conformação desconhecidoMétodo de conformação desconhecido
Dimensões desconhecidasDimensões desconhecidas
3

Fuse on the stopcock

Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).

Materiais para este passo:

Torneira de vidroTorneira de vidro1 plug of glass or PTFE

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
Método de conformação desconhecidoMétodo de conformação desconhecido
4

Make the plastic stem

Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.

Materiais para este passo:

Material desconhecidoMaterial desconhecido1 flexible plastic stem
O-ringO-ring1 peça

Ferramentas necessárias:

Método de conformação desconhecidoMétodo de conformação desconhecido
Dimensões desconhecidasDimensões desconhecidas
5

Assemble and use

Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.

Materiais

4

Ferramentas necessárias

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...