
Simon Says — SIK Circuit 16
Instruções
Parts & Introduction
Parts & Introduction
The grand finale! Simon Says is a memory game where you repeat an ever-growing sequence of colored lights and sounds. This project combines LEDs, buttons, and a buzzer into a complete game with multiple modes. It's the most complex circuit in the SIK — a great capstone project.
Parts Needed
- 1x Arduino Uno + USB cable
- 1x Breadboard
- 4x LEDs (red, green, blue, yellow if possible)
- 4x Push Buttons
- 1x Piezo Buzzer
- 4x 330Ω Resistors
- 17x Jumper Wires
Game Modes
- Memory Mode (default) — Follow the growing pattern. Win after 13 rounds.
- Battle Mode (hold green at startup) — Two-player mode, each player extends the sequence.
- Easter Egg (hold yellow at startup) — Plays "Stayin' Alive" with flashing LEDs!
Materiais para este passo:
SparkFun Inventors Kit - V3.21 kit
Arduino Uno R31 peça
Breadboard1 peça
5mm LED4 peças
Push Button4 peças
330 Ohm Resistor4 peças
Jumper Wires12 peçasFerramentas necessárias:
Hardware Hookup
Hardware Hookup
Wiring Instructions
Pin Assignments
| Component | Arduino Pin |
|---|---|
| Red LED | 10 |
| Green LED | 3 |
| Blue LED | 13 |
| Yellow LED | 5 |
| Red Button | 9 |
| Green Button | 2 |
| Blue Button | 12 |
| Yellow Button | 6 |
| Buzzer pin 1 | 4 |
| Buzzer pin 2 | 7 |
- Each LED needs a 330Ω resistor between its negative leg and GND.
- Buttons use
INPUT_PULLUPmode — connect one side to the pin, other side to GND. No external resistors needed. - The buzzer uses two pins for push-pull drive (louder sound).
- Important: Make sure both GND rails on the breadboard are connected together!
Materiais para este passo:
5mm LED4 peças
Push Button4 peças
330 Ohm Resistor4 peças
Breadboard1 peça
Jumper Wires12 peçasArduino Code
Arduino Code
Open the Arduino IDE and upload the following sketch to your Arduino board.
Materiais para este passo:
Arduino Uno R31 peçaFerramentas necessárias:
Test & Experiment
Test & Experiment
What You Should See
The game starts with a victory sound, then LEDs cycle in an "attract mode" pattern. Press any button to start playing:
- A random LED lights up with a tone — press the matching button.
- The sequence grows by one each round.
- Win after 13 correct rounds! Lose if you press wrong or take too long (3 seconds).
Troubleshooting
- Only half the circuit works: Make sure both GND rails on the breadboard are connected together!
- No sound: Check that both buzzer pins are in the correct rows.
- Buttons not responding: Pay close attention to which pin connects to each button. The
INPUT_PULLUPmode means buttons read LOW when pressed.
Experiments to Try
- Hold the green button during power-up for Battle Mode (2 players).
- Hold the yellow button during power-up for the Bee Gees easter egg!
- Modify
ROUNDS_TO_WINto make the game easier or harder. - Change
ENTRY_TIME_LIMITto give more or less time per button press.
Materiais
8- R$545.00
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 4 peçasR$7.00
- Piezo Buzzer1 peça
- R$14.00
- R$22.00
You can swap these in
Can't get one of the materials? Swap it for an equivalent — these work just as well.
- Instead of Arduino Uno R3, try:
Prototyping Shield for Arduino Uno (3-Pack)
Arduino Uno R3 Board
Arduino Uno - Instead of 5mm LED Assortment Kit (300pcs, 5 Colors), try:
WS2812B NeoPixel LED Strip (1m, 60 LEDs)
Diffused LED - 10mm
RGB LED Strip 5050 (5m, Non-Addressable)
LilyPad Tri-Color LED
SMD LED 0603 - Strip of 25 - Instead of Push Button - 33mm, try:
Concave Retro Gaming Button
Toggle & Duffle Coat Button Set - Instead of Resistor 330 Ohm 1/6 Watt PTH - 20 pack, try:
Resistor 10K Ohm 1/6th Watt PTH - 20 pack
AVR ISP Shield - PTH Kit
Recommended for this build
Products makers often use with builds like this one.
Resistor 10K Ohm 1/6th Watt PTH - 20 packUsed together and in similar builds
Basic 16x2 Character LCD - 5VUsed in similar builds
PotentiometerUsed together and in similar builds
BC547 NPN Transistor (50-Pack)Frequently used with this build's materials
Diode KitFrequently used with this build's materials
LED - RGB Diffused Common Cathode - 5mmFrequently used with this build's materials
Jumper Wire Kit (350pcs, M-M / M-F / F-F)Frequently used with this build's materials
Servo MotorFrequently used with this build's materialsRelated blueprints
Other builds that share materials, tools, or techniques with this one.






CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.