Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Siphon Tube: Glass Tube Bent with Drawn-Down Ends (Faraday, 1830)
Charlie

Criado por

Charlie

7. novembro 2026DE
6
0
0
0
0

Siphon Tube: Glass Tube Bent with Drawn-Down Ends (Faraday, 1830)

A glass siphon for drawing clear liquid off a settled deposit, which Michael Faraday (1830) rated far better than pouring. He bends a glass tube about 0.3 inch inside and 22 inches long so that one leg is about 2 inches longer than the other, and draws both ends down to about 0.2 inch. The narrow ends hold the liquid in while one end is closed with a finger; the wide body lets it run fast. Source: M. Faraday, Chemical Manipulation (1830), §550, pp. 241-242. Picture: his text and figure.
Intermediário
Unknown

Instruções

1

Read Faraday

"Let a piece of glass tube, about 0.3 of an inch internal diameter, 22 inches in length, and of sufficient thickness to bear ordinary laboratory work, be bent at the blow-pipe table, so that one limb shall be about two inches longer than the other; the extremities should be contracted at the lamp, until about 0.2 of an inch in diameter."
2

Cut the tube

Take glass tube about 0.3 in. inside diameter, thick enough for ordinary laboratory work, and cut 22 in. off it: make a deep mark round it with the edge of a sharp three-square file, then break it like a stick, pulling the hands slightly apart (§1152). Wall thickness in figures is not given (unknown).

Materiais para este passo:

Tubo de vidroTubo de vidro1 22 in.

Ferramentas necessárias:

Limas (lima de mão)Limas (lima de mão)
3

Bend it

Bend the tube in the flame of the blow-pipe table so that one leg is about 2 in. longer than the other. For so sharp a bend, do not bend it all at one spot: heat and bend one part as far as it will go without narrowing the bore, then heat the next part and carry the curve on until the legs are close (§1160).

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
4

Draw down the ends

Heat each end and pull it along its length so that it lengthens and narrows (§1166), until the opening is about 0.2 in. across.

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
5

Use it

Hold the siphon upside down with the short leg higher, fill it with water from Faraday's dropping-bottle (a wash bottle does the same job), holding its beak against the side of the opening so no air bubbles are caught; close the long leg with a finger and fill the short leg too. Turn it over, put the short leg into the liquid and lift the finger: the clear liquid runs out. A finger on the outer end slows or stops it; keep the inner end clear of the deposit (§§550-551).

Ferramentas necessárias:

Pisseta de laboratórioPisseta de laboratório

Materiais

1

Ferramentas necessárias

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...