Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)
Ed

Criado por

Ed

4. novembro 2026FI
9
0
0
0
0

Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)

A breadboard lets you build a circuit without solder: push component leads into holes and spring contacts underneath join them in rows. John N. Tengler of A P Products received US 4,420,215 (1983) for one: a one-piece moulded acetal housing with holes on 0.100 in centres, and sets of three springy cantilever contacts of copper alloy No. 688 pushed in from below. Not given: the contact thickness and sizes, how the contacts are formed, and the moulding conditions. Source: J. N. Tengler, US 4,420,215. Picture: the patent's drawing sheet.
Avançado
Not given in the source

Instruções

1

Mould the housing

Injection-mould the housing as one piece in acetal copolymer (Tengler names CELCON). His example has 78 cells in 26 rows of three, open at the bottom, under a top wall whose holes sit on 0.100 in centres. Give each cell two preload bars on its front wall, one either side of the hole, with tapered lower ends. Mould notches into the walls between the cells of a row, and none into the front and back walls, so a contact set fits only the right way round.

Materiais para este passo:

Grânulos de copolímero de acetalGrânulos de copolímero de acetal1 one housing

Ferramentas necessárias:

Máquina de moldação por injeçãoMáquina de moldação por injeção
Estrutura de molde de injeçãoEstrutura de molde de injeção
Dimensões desconhecidasDimensões desconhecidas
2

Form the contact sets

Form three identical contacts from copper alloy No. 688, joined at the foot by a strip. Each is a single cantilever: a foot with a seat, an arm curving up into a spring, a hairpin bend, then a contact face that a pushed-in lead slides along, ending in a tip, with a stop extension that comes to rest against the arm. If you like, stamp a small barb in the joining strip.

Materiais para este passo:

Fita de liga de cobre 688Fita de liga de cobre 6881 one set of three per row

Ferramentas necessárias:

Método de conformação desconhecidoMétodo de conformação desconhecido
Dimensões desconhecidasDimensões desconhecidas
3

Push the sets in from below

Push each set up into its row from the open bottom, contact faces toward the holes, with the strip running through the notches. The strip is bent at a slight angle, so the front wall springs it and wedges the contact's foot against the back wall. The preload bars press on the contact face, and the barb, if there is one, bites into the plastic.

Ferramentas necessárias:

Alicate de bico chatoAlicate de bico chato
4

Check a row

Push a resistor lead through a hole: it should slide along the contact face. The two end contacts of a row join two components; Tengler meant the middle one for injecting or testing a signal. Check with a meter that the three holes of a row connect and neighbouring rows do not.

Ferramentas necessárias:

ResistênciaResistência
MultímetroMultímetro

Materiais

2

Ferramentas necessárias

7

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...