Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)
Charlie

Criado por

Charlie

31. outubro 2026DE
12
0
0
0
0

Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)

A short-stroke solenoid that opens an air valve. One coil pulls the iron armature down; a second, weaker coil holds it there against the air pressure once the first is switched off. A cast-iron shell closes the magnetic circuit around both. Result: an iron-clad plunger solenoid driving a brass valve rod through its hollow core. Source: C. P. Nachod's test (Electrical World, 1905) in Underhill, Solenoids, Electromagnets and Electromagnetic Windings (1910), pp. 125-129. Unknown: the wire insulation; the test does not give it. Not given: shell and armature sizes, voltage. Picture drawn by Youblob.
Avançado
2 days

Instruções

1

Turn the core and armature

Turn the core from Norway iron to 3.17 cm outside diameter and bore a 0.95 cm hole through it for the valve rod. Turn the armature from the same iron. Ours: wrought iron bar; the armature size is not given.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 as required

Ferramentas necessárias:

Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)
2

Cast the shell and top

Cast the shell and top in cast iron so they close the magnetic circuit round the coils, leaving a round clearance gap for the armature in the top. Sizes: not given (Underhill's Fig. 92 shows the layout).

Materiais para este passo:

Lingotes de ferro-gusaLingotes de ferro-gusa1 as required

Ferramentas necessárias:

Forno de cubaForno de cuba
Caixa de moldaçãoCaixa de moldação
Areia de fundiçãoAreia de fundição
3

Wind coil A: 1860 turns of No. 25

Wind the operating coil, 1860 turns of No. 25 wire, and place it where it encircles the working air gap between armature and core. Copper, as Underhill gives for magnet windings. Unknown: the insulation; the test does not give it.

Materiais para este passo:

Fio de cobreFio de cobre1 as required
Material isolante desconhecidoMaterial isolante desconhecido1 as required

Ferramentas necessárias:

Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)
4

Wind coil B: 1765 turns of No. 26

Wind the retaining coil, 1765 turns of No. 26 wire, and place it below coil A on the core. Being away from the gap, it pulls only 0.4-0.8 as hard as A, enough to hold the armature down.

Materiais para este passo:

Fio de cobreFio de cobre1 as required

Ferramentas necessárias:

Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)
5

Assemble with the brass valve rod

Fit core, coils and armature in the shell and pass the brass rod through the core to the valve. Nachod set test gaps of 0.41 and 2.05 mm with brass washers.

Materiais para este passo:

Varão de latãoVarão de latão1 as required

Ferramentas necessárias:

Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)

Materiais

5

Ferramentas necessárias

4

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...