Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)
Charlie

Criado por

Charlie

7. novembro 2026DE
11
0
0
0
0

Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)

A small glass lamp that burns alcohol for heating test tubes and small vessels on the bench. Campbell Morfit (1849): the glass body holds the alcohol; a round copper shield with a tube in its centre carries a cotton wick and rests on the neck; a minute hole in the shield lets vapour escape; a glass cap ground to fit the neck keeps the alcohol from evaporating. Alcohol gives no smoke and does not blacken the glass. Sizes, and how the wick tube is fixed, are not given. Source: C. Morfit, Chemical and Pharmaceutic Manipulations (1849), pp. 160-162. Picture: Fig. 115.
Iniciante
Unknown

Instruções

1

Read Morfit

"To the neck b is adjusted a copper circular shield c, with a tube in its centre for the passage of the wick, which should be of cotton, and similar to that used for tallow candles. The shield should rest upon, rather than within the neck, otherwise its expansion by the heat may cause the breakage of the glass. A minute opening drilled in the shield is also requisite for the escape of vapor in case the alcohol should become heated."
2

Make the copper shield

Cut a round copper shield a little wider than the neck of the glass body, so it rests on the neck and not inside it. Fix a short copper tube through its centre for the wick (ours: soldered; the joint is not given). Drill a minute hole in the shield for vapour to escape. Sizes are not given (unknown).

Materiais para este passo:

Chapa de cobreChapa de cobre1 shield
Tubo de cobreTubo de cobre1 wick tube
Solda de estanho-chumboSolda de estanho-chumbo1 joint
FluxoFluxo1 joint

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Ferro de soldarFerro de soldar
Berbequim de mãoBerbequim de mão
Dimensões desconhecidasDimensões desconhecidas
3

Fit the wick and the body

Draw a cotton wick of the tallow-candle kind through the tube so it reaches down into the glass body, which is the alcohol reservoir. Set the shield on the neck. Ours: a clear glass bottle as the body.

Materiais para este passo:

Garrafa de vidro (transparente)Garrafa de vidro (transparente)1 body
Pavio de algodão para velasPavio de algodão para velas1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
4

Fit the glass cap

Cover the wick, when the lamp is not in use, with a glass cap ground inside to fit the neck closely. It stops the alcohol evaporating and the wick taking up water, which makes relighting difficult. Put it on only after the lamp is out. How the cap is made and ground is not given (unknown).

Materiais para este passo:

Vidro desconhecidoVidro desconhecido1 cap

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
5

Fill and use

Morfit burns alcohol of about specific gravity 0.85. Always put the lamp out before refilling, then pour the spirit in gently until the reservoir is nearly full. The flame is hottest just below its tip; bring the vessel to it gradually, and spread the heat with copper gauze between flame and vessel for larger surfaces.

Materiais

7

Ferramentas necessárias

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...