Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Criado por

Woody

13. novembro 2026NO
6
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
Avançado
Several weeks

Instruções

1

His layout data

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco4 peças
Tábua de cedroTábua de cedro6 peças
Tábua de pinhoTábua de pinho3 peças

Ferramentas necessárias:

Serrote de corte ao fioSerrote de corte ao fio
SerroteSerrote
Plaina manualPlaina manual
Fita métricaFita métrica
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Materiais para este passo:

Tábua de pinhoTábua de pinho2 peças
Folhas de papel grossoFolhas de papel grosso1 peça
PregosPregos1 peça

Ferramentas necessárias:

SerroteSerrote
Serra de recortesSerra de recortes
RéguaRégua
LápisLápis
TesouraTesoura
MarteloMartelo
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco2 peças
Parafusos de latão para madeiraParafusos de latão para madeira4 peças

Ferramentas necessárias:

Faca de dois cabosFaca de dois cabos
Plaina manualPlaina manual
SerroteSerrote
Arco de pua e brocaArco de pua e broca
Chave de fendasChave de fendas
Grampo em CGrampo em C
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco2 peças
Tábua de pinhoTábua de pinho1 peça
PregosPregos1 peça

Ferramentas necessárias:

Esquadro fixoEsquadro fixo
MarteloMartelo
FormõesFormões
Plaina manualPlaina manual
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Materiais para este passo:

Tábua de cedroTábua de cedro2 peças
Pregos de cobre de cabeça largaPregos de cobre de cabeça larga1 peça

Ferramentas necessárias:

SerroteSerrote
MarteloMartelo
Fita métricaFita métrica
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Materiais para este passo:

Tábua de cedroTábua de cedro4 peças
Pregos de cobre de cabeça largaPregos de cobre de cabeça larga1 peça
Tachas de cobreTachas de cobre1 peça

Ferramentas necessárias:

SovelaSovela
Grampo em CGrampo em C
Ferro de rebaterFerro de rebater
MarteloMartelo
SerroteSerrote
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco2 peças
Tábua de cedroTábua de cedro1 peça
Pregos de cobre de cabeça largaPregos de cobre de cabeça larga1 peça
Parafusos de latão para madeiraParafusos de latão para madeira30 peças
Lona de algodãoLona de algodão1 peça

Ferramentas necessárias:

Arco de pua e brocaArco de pua e broca
Chave de fendasChave de fendas
SerroteSerrote
FormõesFormões
MarteloMartelo
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Materiais para este passo:

Lona de algodãoLona de algodão1 peça
Cola marítimaCola marítima1 peça
Tachas de cobreTachas de cobre1 peça

Ferramentas necessárias:

LataLata
Trincha largaTrincha larga
Ferro de passar de chapaFerro de passar de chapa
TesouraTesoura
MarteloMartelo
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Materiais para este passo:

Moldura de madeira meia-canaMoldura de madeira meia-cana1 peça
Chapa de latão para roda de proaChapa de latão para roda de proa2 peças
Parafusos de latão para madeiraParafusos de latão para madeira12 peças
Tábua de carvalho-brancoTábua de carvalho-branco1 peça
PregosPregos1 peça

Ferramentas necessárias:

MarteloMartelo
Chave de fendasChave de fendas
Plaina manualPlaina manual
Berbequim de mãoBerbequim de mão
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Materiais para este passo:

Verniz de goma-lacaVerniz de goma-laca1 peça
Tinta de óleoTinta de óleo1 peça
LixaLixa1 peça
Verniz marítimoVerniz marítimo1 peça
Tábua de pinhoTábua de pinho1 peça

Ferramentas necessárias:

Trincha largaTrincha larga
Chave de fendasChave de fendas
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Materiais

16

Ferramentas necessárias

21

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...