ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
The Die-Spindle Ticket Punch: A Shaped Die on a Pivot, a Slot for the Ticket
Every conductor on a railway line cancelled tickets with a punch of his own shape, and a punch whose die rode loosely in its lever cut ragged holes.
William J. Phelps of Springfield, Massachusetts, received US 69,019, dated 17 September 1867, for "attaching to one of the levers of a ticket-punch a die-spindle, which is pivoted to the lever, and operates as a plunger in reference to a female die seated in the other lever of the punch, the latter lever being slotted for the reception of the ticket to be punched." The spindle's lower end is cut to any shape, "the case that different persons employed in cancelling tickets upon the same route have punches of different configuration"; a spiral spring keeps the levers apart and a finger loop hangs the punch from the finger.
This rung works out the force to punch a ticket, then files the levers from flat bar with a pivoted spindle, a hardened die plate and a shaped cutting end, and punches card with it.
Avançado
About 6 hours
Instruções
1
1
Punching force
Punching force
A carregar o notebook Jupyter…
2
2
A ticket punch a week before it
A ticket punch a week before it
The embedded blueprint is a ticket punch patented a week earlier. Phelps pivots the cutting spindle to one lever so it enters its die in line.
3
3
Read US 69,019
Read US 69,019
"A slot, n, is cut in the lower side of A, of sufficient width to receive a ticket or strip of pasteboard, the outer end of the slot being made flaring, so as to facilitate the insertion of the ticket which is to be punched. The die-spindle h passes through an opening, p, formed in that part of A above the slot n, the shape of the inner surface of p being made to correspond with the shape of the die-spindle, so as to act as an accurate guide for the latter as it is moved to and from the female die m."
"The contour of the female die is made to correspond exactly with that of the male die, and the edges of both are carefully formed, so as to make a sharp and clean cut when the male die is made to enter the female die."
4
4
Make the punch and cancel tickets
Make the punch and cancel tickets
**Levers.** Cut two 16 cm levers from 20 × 5 mm mild steel flat bar, shaped as Phelps's: A with a finger loop bent from its end and a slot n sawn across its jaw with a flared mouth, B slimmer beyond its shoulders. Drill both for a pivot pin.
**Guide and die.** Drill A's jaw above the slot for the spindle as the guide p, and set a small hardened steel plate m below the slot, drilled with the female die and relieved underneath so the chips fall out.
**Spindle.** File a 5 mm steel rod's lower end to your chosen shape, a star or letter, and file the female die to match it exactly. Pin the spindle's upper end between two ears on lever B so it swings into the guide.
**Spring.** Put a compression spring between the levers behind the pivot to hold them open.
**Test.** Slide card into the slot and squeeze. Look at the hole's edges through a magnifier, and punch a hundred holes to see whether they stay clean.
Materiais para este passo:
Barra chata de aço macio0.35 metro
Varão de aço macio0.1 metro
Chapa grossa de aço macio1 peça
Sortido de molas de compressão1 peça
Rebites cegos2 peças
Cartolina1 peçaFerramentas necessárias:
Serra de arco para metais
Limas (lima de mão)
Jogo de limas de agulha
Torno de bancada
Berbequim sem fios
Jogo de brocas
Maçarico a propano
Martelo
Paquímetro digital de 6 polegadas
Luvas de trabalho em couro
Óculos de segurança transparentes5
5
A punch that tears, jams or misses its die
A punch that tears, jams or misses its die
Die-spindle ticket punch troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**William J. Phelps** of Springfield, Hampden County, Massachusetts, received US 69,019, dated 17 September 1867. His lever B was curved at a and thinned from the shoulders K K to fit a recess f f′ in lever A, the ears g g received the spindle, a steel die plate m was set into a brass lever, and a spring C in recesses o and e held the levers apart. He did not claim the ticket slot or the levers' arrangement apart from the die-spindle, but the lever B with the pivoted spindle, the slotted lever, guide and female die, with the spring.
**Honest limits.** Filed flat bar and a hardened rod stand in for his cast levers. The notebook uses a simple shear formula; its strength, thickness and shapes are examples. Your cancelled tickets are the result.
Materiais
6- 0.35 metroReferência
- 0.1 metroReferência
- Referência
- Referência
- 2 peçasReferência
- 1 peçaReferência
Ferramentas necessárias
11- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios
The Cushioned Ticket Punch: A Spring That Strips the Ticket and Rings That Carry the Joint
por Martin
Ferramentas de Artesanato em Papel
10
0
0
0
0
0
Blanking: The Punch, the Die, and the Gap Between Them
por Forge
Trabalho em Metal
17
0
0
0
0
0
Punching and Drifting: A Hole Without Removing Metal
por Forge
Trabalho em Metal
18
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.