ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It
Martin

Criado por

Martin

6. outubro 2026NO
3
0
0
0
0

The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It

Scrubbing a floor means going back to the bucket every few strokes. Ernest N. Broderick of Indianapolis received US 639,348, dated 19 December 1899, for a cleaning brush with a small tank on its perforated top, fed through a hollow handle from a hose; a perforated plate slid by a screw sets how far the holes open, and soap in the tank turns the water to suds — "a self-feeding brush." This rung works out how the sliding plate opens the holes, then builds the tank on a scrub brush and measures the flow at each plate setting.
Intermediário
About 4 hours

Instruções

1

Open area of the plate

A carregar o notebook Jupyter…
2

A scrubbing brush before it

The embedded blueprint holds two brush heads on a sprung holder. Broderick puts a water tank on the head and feeds it through the handle.
3

Read US 639,348

"When used for scrubbing, the hose can be connected to a hydrant, and thus supply the desired amount of water to the brush, making it unnecessary to dip the brush into the bucket or tub of water. In other words, my device is a self-feeding brush. Should I desire to use soapy water, I can insert through the openings 10 particles of soap or soap powder. In this way I get soapsuds, which I use in scrubbing as it is needed, keeping the brush constantly supplied."
4

Perforate the brush back

Drill fourteen 4 mm holes through the scrub brush's back between the tufts, in two rows 30 mm apart.

Materiais para este passo:

Escova de esfregarEscova de esfregar1 peça

Ferramentas necessárias:

Torno de bancadaTorno de bancada
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Marcador permanenteMarcador permanente
RéguaRégua
Óculos de segurança transparentesÓculos de segurança transparentes
5

Make the sliding plate

Cut an aluminium plate 10 mm shorter than the back. Drill it through the back's holes, then file its end square. Rivet two guide strips to the back's top so it slides lengthwise.

Materiais para este passo:

Chapa de alumínioChapa de alumínio1 peça
Rebites cegosRebites cegos1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
Kit de rebitadoraKit de rebitadora
6

Build the tank

Fold an aluminium box 50 mm deep to the back's size with a lid. Drill the lid for a 25 mm filling hole and a handle socket. Seal it to the back with silicone and screws.

Materiais para este passo:

Chapa de alumínioChapa de alumínio1 peça
Rebites cegosRebites cegos1 peça
Vedante de siliconeVedante de silicone1 peça
Parafuso para madeira n.º 8 x 1"Parafuso para madeira n.º 8 x 1"1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Torno de bancadaTorno de bancada
Kit de rebitadoraKit de rebitadora
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Luvas de trabalho em couroLuvas de trabalho em couro
7

Fit the adjusting screw

Run an M4 screw through a nut epoxied on the tank's end wall so its tip pushes the plate. Turn it to close or open the holes.

Materiais para este passo:

Parafusos de máquinaParafusos de máquina1 peça
Porca sextavadaPorca sextavada1 peça
Epóxi de dois componentesEpóxi de dois componentes1 peça

Ferramentas necessárias:

Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Fit the handle

Fix 1.2 m of 15 mm copper tube in the socket with brass fittings. Fit a ball valve and hose connector at its top.

Materiais para este passo:

Tubo de cobreTubo de cobre1 peça
Acessórios de latãoAcessórios de latão1 peça
Válvula de esferaVálvula de esfera1 peça
Fita de PTFE para roscasFita de PTFE para roscas1 peça

Ferramentas necessárias:

Corta-tubosCorta-tubos
Chave inglesa ajustávelChave inglesa ajustável
9

The patent drawing

US 639,348 drawing sheet, public domain (expired patent).
Passo 9 - Image 1
10

Measure the flow at each setting

Connect the garden hose. Set the plate fully open, half and nearly shut, and catch the water for 30 s each in the jug. Then add a squirt of soap through the filling hole and scrub.
Passo 10 - Image 1

Materiais para este passo:

Mangueira de jardimMangueira de jardim1 peça
ÁguaÁgua1 peça
Sabão de Castela líquidoSabão de Castela líquido1 peça

Ferramentas necessárias:

Jarro medidorJarro medidor
CronómetroCronómetro
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
11

A brush that floods, starves or leaks

Tank-headed self-feeding brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Ernest N. Broderick** of Indianapolis filed US 639,348 on 6 February 1899; it is dated 19 December 1899. Rubber or leather strips seal the tank to the brush-top. Two hollow adjustable joints, ground to fit and clamped by a bolt, let the handle be set at any angle, for floors, walls, windows or dusting high furniture; with compressed air instead of water it blows dust away, and a mop or duster may replace the brush. **Honest limits.** Our handle is fixed; his joints are not built here. The notebook gives open area, not flow through a real hole. Your flows are the result.

Materiais

15

Ferramentas necessárias

16

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...