Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Thompson (Nlaka'pamux) Smoked Buckskin: Scraped on a Leaning Poplar Log with a Deer Ulna, Soap-Soaked, Wrung, Pounded Soft, Smoked (Teit, 1900)
Tex

Criado por

Tex

15. novembro 2026FO
9
0
0
0
0

Thompson (Nlaka'pamux) Smoked Buckskin: Scraped on a Leaning Poplar Log with a Deer Ulna, Soap-Soaked, Wrung, Pounded Soft, Smoked (Teit, 1900)

The Thompson (Nlaka'pamux) buckskin James Teit saw made around 1900: a soaked hide scraped on a peeled poplar log leaning against a tree with a deer's ulna or a horse rib used like a draw-knife, smoked over a small pit of smouldering rotten wood, soaked a day in soapy water, wrung with dry grass on a log and stick, pounded soft on a frame and smoked again.
Avançado
About a week

Instruções

1

Read Teit

"It is said that, after being smoked, the skin does not shrink so much when it gets wet as it otherwise would."
2

Soak and set up the log

Soak the dry skin in water for several days. Peel a poplar log about 5 in. (13 cm) thick and 4 ft (1.2 m) long; stand one end on the ground and lean the other against a tree, in a notch cut in its bark.

Materiais para este passo:

Couro cruCouro cru1 peça
ÁguaÁgua1 peça
Varas de madeira verdeVaras de madeira verde1 peça

Ferramentas necessárias:

Cavalete de descarnarCavalete de descarnar
3

Scrape both sides

Lay the skin loosely over the log with some hanging over the top so the pressure holds it. Scrape the flesh side with a slightly sharpened deer ulna or horse rib held at both ends like a draw-knife, moving the skin as you go; then the hair side, taking the dark outer skin off with the hair. Bone cuts the skin less than iron.

Ferramentas necessárias:

DescarnadeiraDescarnadeira
Cavalete de descarnarCavalete de descarnar
4

Dry and smoke

Hang it over a pole to dry. Dig a hole about 1½ ft (45 cm) deep and a little over 1 ft (30 cm) across, light a smouldering fire of rotten fir wood (fir bark with dry pine cones is best; juniper for a very dark colour), set a frame of bent sticks over it, spread the skin on it and cover all with an old blanket. Turn it to smoke the other side.

Materiais para este passo:

Madeira podreMadeira podre1 peça
Vime de salgueiroVime de salgueiro1 peça

Ferramentas necessárias:

PáPá
FogueiraFogueira
Lona de algodãoLona de algodão
Vara de madeiraVara de madeira
5

Soap, wring and pound

Soak it 24 hours or more in warm water with a strong soap solution. Roll it lengthwise with a little dry grass, tie one end to a log with a rope, fold the other round a short stout stick and turn until the water is wrung out. Stretch it on a frame and pound the inside until quite dry and soft (warm it by a fire in cold weather), then smoke it again.

Materiais para este passo:

SabãoSabão1 peça
ÁguaÁgua1 peça
FenoFeno1 peça

Ferramentas necessárias:

Panela grande de tingirPanela grande de tingir
CordaCorda
Pá de madeiraPá de madeira
Vara de madeiraVara de madeira
6

Troubleshooting

Smoked buckskin troubleshooting.

Flow

Loading...
7

History and honest limits

From James Teit, *The Thompson Indians of British Columbia*, **Memoirs of the American Museum of Natural History, Jesup North Pacific Expedition** vol. I part IV (1900), pp. 185-186 and Figs. 127-129 (checked on the archive.org scan cihm_16242). Some said smoking came from the Okanagon; many held that a skin rubbed with brains needs no smoking (see the Navajo brain-tan blueprint). Corncob smoke gave a bright yellow. Frame size and hay for the dry grass are ours.

Materiais

7
  • 1 peça
    Referência
  • 2 peças
    Referência
  • Referência
  • Referência
  • Referência
  • 1 peça
    Referência
  • 1 peça
    Referência

Ferramentas necessárias

9

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...