Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Uncapping Tray: McIntyre's Uncapping Box (A B C of Bee Culture, 1910)
Woody

Criado por

Woody

4. novembro 2026NO
10
0
0
1
0

Uncapping Tray: McIntyre's Uncapping Box (A B C of Bee Culture, 1910)

A big wooden uncapping box from a California honey producer: 6 ft long, tin-lined, with a screen on cross strips to catch the cappings and a tin pipe at one end where the honey drains out, and an iron pivot on a cross piece to spin each comb while uncapping. Its length lets the cappings be forked to the far end to drain for 4 or 5 days instead of piling under the knife. Source: J. F. McIntyre in The A B C and X Y Z of Bee Culture (1910), pp. 183-184. Picture: the book's section and view.
Iniciante
Unknown

Instruções

1

Build the box

Make a box 2 ft wide, 2 ft deep and 6 ft long outside of 7/8 in lumber dressed both sides, with the bottom 2 in lower in the middle than at the sides.

Materiais para este passo:

TábuaTábua1 7/8 in lumber

Ferramentas necessárias:

SerroteSerrote
MarteloMartelo
Pregos de ferroPregos de ferro
2

Line it and fit the pipe

Line the bottom with tin to keep it from leaking, and fit a tin pipe at one end for the honey to run out.

Materiais para este passo:

Chapa de folha de flandresChapa de folha de flandres1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
MarteloMartelo
3

Lay the screen

Lay eleven pieces of wood 1 x 1 x 22 in across the bottom about 6 in apart and lay the screen on them, leaving room below for the honey to run to the pipe end.

Materiais para este passo:

TábuaTábua11 1 x 1 x 22 in
Tela de arame tecido para crivoTela de arame tecido para crivo1 peça

Ferramentas necessárias:

SerroteSerrote
4

Narrow the top and fit the pivot

Nail two pieces 7/8 x 3 x 72 in on the top edges, one each side, to narrow the top to the inside length of a Langstroth hive. Fix one piece 7/8 x 3 x 22 1/4 in across the top about 14 in from one end, with an iron pivot sticking up through it 1 1/2 in high to rest the combs on.

Materiais para este passo:

TábuaTábua3 two 7/8 x 3 x 72 in, one 7/8 x 3 x 22 1/4 in
Barras de ferroBarras de ferro1 pivot 1 1/2 in high
Pregos de ferroPregos de ferro1 peça

Ferramentas necessárias:

SerroteSerrote
MarteloMartelo
5

Set it up and use it

Stand the box with its bottom 7 in from the floor so the honey can run into a strainer below; the top is then about 32 in high (make it shallower, or stand on a plank, for a shorter person). Set one end of a comb on the pivot, uncap one side, whirl it round and uncap the other, then stand the comb in the end of the box.

Ferramentas necessárias:

MarteloMartelo

Materiais

5

Ferramentas necessárias

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...