Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Intermediário
Unknown
Instruções
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
Materiais para este passo:
Tábua de freixo1 hales 3 ft 1 in x 1 5/8 x 1 1/2 inFerramentas necessárias:
Serrote
Plaina manual
Plaina de raspar curvas2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
Materiais para este passo:
Tábua de carvalho-branco1 peça
Cavilha de madeira1 3/16 in pinsFerramentas necessárias:
Serrote de costas
Formão de samblagem
Graminho
Arco de pua e broca
Suta3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
Materiais para este passo:
Tábua de carvalho-branco1 legs 1 1/2 in square, stays
Parafuso de carroçaria4 3 inFerramentas necessárias:
Serrote
Arco de pua e broca
Conjunto de chaves de fendas4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
Materiais para este passo:
Tábua de pinho1 1/2 in bottom, 5/8 in sides
Tinta de óleo1 peçaFerramentas necessárias:
Serrote
Plaina manual
Conjunto de pincéis5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
Materiais para este passo:
Tábua de pinho1 3/4 in front board
Pregos de ferro1 1 1/2 in cut nails
Barra chata de aço macio1 7/8 in hoop iron
Parafusos para madeira1 3/4 in round-headed
Tinta de óleo1 peçaFerramentas necessárias:
Serrote
Martelo
Conjunto de chaves de fendas
Conjunto de pincéis6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
Materiais para este passo:
Tábua de freixo1 axle and felloes
Tábua de carvalho-branco1 spokes
Vareta de ferro1 3/8 in pins
Cavilha de madeira4 1/4 in
Barra chata de aço macio1 3/4 x 1/8 in tyreFerramentas necessárias:
Torno de madeira
Plaina de raspar curvas
Arco de pua e broca
Martelo7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
Materiais para este passo:
Barra chata de aço macio2 3/4 x 1/8 in irons
Parafusos para madeira1 peça
Tinta de óleo1 peçaFerramentas necessárias:
Conjunto de chaves de fendas
Conjunto de pincéisMateriais
10- 1 axle and felloesReferência
- 1 spokesReferência
- 4 1/4 inReferência
- 4 3 inReferência
- 1 3/4 in front boardReferência
- 3 peçasReferência
- 1 1 1/2 in cut nailsReferência
- 2 3/4 x 1/8 in ironsReferência
- 1 peçaReferência
- 1 3/8 in pinsReferência
Ferramentas necessárias
12- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
