Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
Forge

Criado por

Forge

15. novembro 2026NO
5
0
0
0
0

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)

C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
Intermediário
A day

Instruções

1

The steps

A carregar o notebook Jupyter…
2

Read Willey

"A very efficient, quick-opening and closing vise for the drill-press table."
3

Make the bed

Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Punção de centroPunção de centro
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
4

Make the end supports

Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
5

Make the fixed jaw

Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Martelo de bolaMartelo de bola
6

Make the sliding jaw

Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Martelo de bolaMartelo de bola
Torno de bancadaTorno de bancada
7

Make the cam

Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.

Materiais para este passo:

Veio de açoVeio de aço1 peça
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Martelo de bolaMartelo de bola
8

Use it

Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.

Materiais para este passo:

Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Engenho de furarEngenho de furar
9

Troubleshooting

Drill vise troubleshooting.

Flow

Loading...
10

History and honest limits

From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.

Materiais

4

Ferramentas necessárias

7

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...