སྒྱུ་རྩལ
མཛེས་སྡུག་དང་བདེ་ཐང
བཟོ་རིག
རིག་གནས་དང་ལོ་རྒྱུས
དགའ་སྟོན
ཁོར་ཡུག
ཟས་དང་བཏུང་རྫས
ཕྱིར་འཕྲུལ་རིག
ཚན་རིག
རྩེད་འགྲན
རིག་རྩལ
གྱོན་རུང
Steel Butt Hinges from Sheet and Rod
Forge

བཟོས་མཁན

Forge

11. སྤྱི་ཟླ་བཅུ་པ 2026NO
༤༠
༠
༠
༠
༠

Steel Butt Hinges from Sheet and Rod

A butt hinge is two flat leaves whose curled edges, the knuckles, interlock round a pin. Each leaf's edge is rolled round a rod the size of the pin; slots are cut so the knuckles alternate; the pin goes through and is peened over. Countersunk holes take the screws.
བར་མ
2 hours per pair

ལམ་སྟོན

1

Cut the leaves

Mark and cut two leaves from 1.5 mm mild steel sheet, 75 by 30 mm plus a curl allowance of about three times the pin's diameter.

གོམ་པ་འདིའི་རྫས་རིགས:

ལྕགས་འཇམ་གྱི་ལེབ་ཤོགལྕགས་འཇམ་གྱི་ལེབ་ཤོག0.01 sqm

ལག་ཆས་དགོས་མཁོ:

ཐིག་འཛུགས་ཁབ།ཐིག་འཛུགས་ཁབ།
ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།
དར་མའི་ཚོགས་ཆས།དར་མའི་ཚོགས་ཆས།
2

Roll the knuckles

Clamp a leaf in the vise with a 4 mm rod along its edge and hammer the edge round the rod, a little at a time, until it closes. Do the second leaf the same way.

ལག་ཆས་དགོས་མཁོ:

ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
མགོ་སྒོར་སྒོར་གྱི་ཐོ་བ།མགོ་སྒོར་སྒོར་གྱི་ཐོ་བ།
3

Cut alternate knuckles

Mark the knuckle into five equal lengths. Saw and file away the 2nd and 4th on one leaf and the 1st, 3rd and 5th on the other, so they mesh.

ལག་ཆས་དགོས་མཁོ:

ལྕགས་གཏུབ་སོག་ལེ།ལྕགས་གཏུབ་སོག་ལེ།
དར་མའི་ཚོགས་ཆས།དར་མའི་ཚོགས་ཆས།
ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6
4

Drill and countersink

Centre-punch three holes in each leaf, drill them for the screws and countersink them.

ལག་ཆས་དགོས་མཁོ:

དབུས་ཀྱི་རྟགས་ཆས།དབུས་ཀྱི་རྟགས་ཆས།
འཁོད་བཞག་ཕུག་འཕྲུལ།འཁོད་བཞག་ཕུག་འཕྲུལ།
ཕུག་མགོའི་ཚོགས་ཆས།ཕུག་མགོའི་ཚོགས་ཆས།
ཀའུན་ཊར་སིངཀ་རྩེ་མོའི་ཆས་ཆཀའུན་ཊར་སིངཀ་རྩེ་མོའི་ཆས་ཆ
5

Pin it

Mesh the knuckles and push a 4 mm mild steel rod through, cut 1 mm proud at each end. Peen both ends over so the pin cannot slide out. Check it swings freely.

གོམ་པ་འདིའི་རྫས་རིགས:

ལྕགས་འཇམ་གྱི་དབྱུག་ཟླུམ།ལྕགས་འཇམ་གྱི་དབྱུག་ཟླུམ།0.1 མི་ཊར།

ལག་ཆས་དགོས་མཁོ:

ལྕགས་གཏུབ་སོག་ལེ།ལྕགས་གཏུབ་སོག་ལེ།
མགོ་སྒོར་སྒོར་གྱི་ཐོ་བ།མགོ་སྒོར་སྒོར་གྱི་ཐོ་བ།
ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
6

Troubleshooting

Butt hinge troubleshooting.

Flow

Loading...

རྫས་རིགས

2

ལག་ཆས་དགོས་མཁོ

11

བིལུ་པིརིན་ཊི་འདི་གིས་བཟོ་མི

འབྲེལ་ཡོད་བིལུ་པིརིན་ཊི

བིལུ་པིརིན་ཊི་འདི་ཚུ་ཐབས་ལམ་དང་རྫས་རིགས། སྤྱི་ཆོས་བགོ་བཤའ་བྱེད

CC0 སྤྱི་དབང

བིལུ་པིརིན་ཊི་འདི་CC0 འོག་བཀྲམས་ཡོད། ཁྱེད་རང་གིས་ཆོག་མཆན་མ་བཞེས་པར་ཕབ་ལེན་དང་བཟོ་བཅོས། བགོ་བཤའ། དགོས་མཁོ་གང་ལའང་བཀོལ་སྤྱོད་བྱས་ཆོག

བཟོ་མཁན་ལ་རྒྱབ་སྐྱོར་བྱེད་པའི་ཆེད་ཁོང་ཚོའི་བིལུ་པིརིན་ཊི་བརྒྱུད་ཐོན་སྐྱེད་ཉོ། བཟོ་མཁན་གྱིས བཟོ་མཁན་གྱི་ཁེ་ཕོགས ཚོང་པས་གཏན་འཁེལ་བྱས་པ། ཡང་ན་བིལུ་པིརིན་ཊི་འདིའི་པར་གསར་བཟོས་ཏེ་ཁྱེད་རང་གི་བིལུ་པིརིན་ཊི་ནང་མཐུད་སྦྲེལ་བྱས་ཏེ་ཡོང་སྒོ་བགོ་བཤའ་བྱེད།

གྲོས་བསྡུར

(0)

ནང་འཛུལ གྲོས་བསྡུར་ནང་མཉམ་ཞུགས་ཆེད

བསམ་ཚུལ་ཚུ་ཐོབ་བཞིན...