སྒྱུ་རྩལ
མཛེས་སྡུག་དང་བདེ་ཐང
བཟོ་རིག
རིག་གནས་དང་ལོ་རྒྱུས
དགའ་སྟོན
ཁོར་ཡུག
ཟས་དང་བཏུང་རྫས
ཕྱིར་འཕྲུལ་རིག
ཚན་རིག
རྩེད་འགྲན
རིག་རྩལ
གྱོན་རུང
Teapot: a Tinplate Picnic Teapot with Cock and Strainer (Hasluck, 1907)
Forge

བཟོས་མཁན

Forge

4. སྤྱི་ཟླ་བཅུ་གཅིག་པ 2026NO
༠
༠
༠
༡
༠

Teapot: a Tinplate Picnic Teapot with Cock and Strainer (Hasluck, 1907)

A square tinplate teapot from a picnic outfit: folded from one blank, with a hinged lid, and a cock at the bottom behind a perforated strainer that holds back the leaves. Blank 1 ft 4 1/4 in by 1 ft 0 3/8 in; lid 4 1/8 by 4 in. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 37-39. Unknown: folding order, solder, the cock. Picture: Figs. 96-97 of the book.
བར་མ
Unknown

ལམ་སྟོན

1

Cut the body blank

Cut a piece of tin 1 ft 4 1/4 in long by 1 ft 0 3/8 in wide and mark the pattern of Fig. 96 on it, with the hole for the cock tube. Not given: the folding order. Ours: bend it up on the dotted lines and solder the seams.

གོམ་པ་འདིའི་རྫས་རིགས:

ཊིན་བྱུགས་ལྕགས་ལེབ།ཊིན་བྱུགས་ལྕགས་ལེབ།1 body
གསའ-ཞ་ཡི་ལྷ་ཡིགགསའ-ཞ་ཡི་ལྷ་ཡིག1 དུམ་བུ།

ལག་ཆས་དགོས་མཁོ:

ཐིག་འཛུགས་ཁབ།ཐིག་འཛུགས་ཁབ།
ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།
ཕུར་པཕུར་པ
ཤིང་གི་ཐོ་བ།ཤིང་གི་ཐོ་བ།
གློག་གི་ཞ་སྦྱར་ལྕགསགློག་གི་ཞ་སྦྱར་ལྕགས
ཞུ་རོགས་རྫསཞུ་རོགས་རྫས
2

Fit the cock and strainer

Solder a tube about 1/2 in long into the hole for the cock (Fig. 97) and fit the cock to it. Develop the strainer (Fig. 98): top curve radius 1 13/16 in, chord corner to corner 2 15/16 in. Perforate it and solder it across the corner in front of the tube (Fig. 99).

གོམ་པ་འདིའི་རྫས་རིགས:

རག་གི་ དོང་པོ།རག་གི་ དོང་པོ།1 1/2 in
བཏོན་ནིའི་ཆུ་སྒོ།བཏོན་ནིའི་ཆུ་སྒོ།1 དུམ་བུ།
ཊིན་བྱུགས་ལྕགས་ལེབ།ཊིན་བྱུགས་ལྕགས་ལེབ།1 strainer
གསའ-ཞ་ཡི་ལྷ་ཡིགགསའ-ཞ་ཡི་ལྷ་ཡིག1 དུམ་བུ།

ལག་ཆས་དགོས་མཁོ:

རྩེ་གཉིས་ཀྱི་སྐོར་ཐིག་ཆས།རྩེ་གཉིས་ཀྱི་སྐོར་ཐིག་ཆས།
ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།
ལྕགས་ལེབ་ཁུང་བུ་གཏོད་ཆས།ལྕགས་ལེབ་ཁུང་བུ་གཏོད་ཆས།
སྲ་བའི་ཤིང་གི་སྒོ་རྡོགསྲ་བའི་ཤིང་གི་སྒོ་རྡོག
གློག་གི་ཞ་སྦྱར་ལྕགསགློག་གི་ཞ་སྦྱར་ལྕགས
ཞུ་རོགས་རྫསཞུ་རོགས་རྫས
3

Make the hinged lid

Cut the lid (Fig. 100) 4 1/8 by 4 in; the inner rectangle 3 1/2 by 3 1/2 in leaves 1/4 in to bend up. Cut hinge projections 1/2 in wide by 5/8 in deep with equal spaces, the outer ones only 1/4 in wide. Bend them round a wire 1/16 in thick. Hasluck adds that the teapot may be enamelled dark green.

གོམ་པ་འདིའི་རྫས་རིགས:

ཊིན་བྱུགས་ལྕགས་ལེབ།ཊིན་བྱུགས་ལྕགས་ལེབ།1 lid
ལྕགས་སྐུདལྕགས་སྐུད1 1/16 in

ལག་ཆས་དགོས་མཁོ:

ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།ལྕགས་ལེབ་གཏུབ་ནིའི་ཇེམ་ཙི།
ཕུར་པཕུར་པ
ཤིང་གི་ཐོ་བ།ཤིང་གི་ཐོ་བ།

རྫས་རིགས

5

ལག་ཆས་དགོས་མཁོ

9

བིལུ་པིརིན་ཊི་འདི་གིས་བཟོ་མི

CC0 སྤྱི་དབང

བིལུ་པིརིན་ཊི་འདི་CC0 འོག་བཀྲམས་ཡོད། ཁྱེད་རང་གིས་ཆོག་མཆན་མ་བཞེས་པར་ཕབ་ལེན་དང་བཟོ་བཅོས། བགོ་བཤའ། དགོས་མཁོ་གང་ལའང་བཀོལ་སྤྱོད་བྱས་ཆོག

བཟོ་མཁན་ལ་རྒྱབ་སྐྱོར་བྱེད་པའི་ཆེད་ཁོང་ཚོའི་བིལུ་པིརིན་ཊི་བརྒྱུད་ཐོན་སྐྱེད་ཉོ། བཟོ་མཁན་གྱིས བཟོ་མཁན་གྱི་ཁེ་ཕོགས ཚོང་པས་གཏན་འཁེལ་བྱས་པ། ཡང་ན་བིལུ་པིརིན་ཊི་འདིའི་པར་གསར་བཟོས་ཏེ་ཁྱེད་རང་གི་བིལུ་པིརིན་ཊི་ནང་མཐུད་སྦྲེལ་བྱས་ཏེ་ཡོང་སྒོ་བགོ་བཤའ་བྱེད།

གྲོས་བསྡུར

(0)

ནང་འཛུལ གྲོས་བསྡུར་ནང་མཉམ་ཞུགས་ཆེད

བསམ་ཚུལ་ཚུ་ཐོབ་བཞིན...