སྒྱུ་རྩལ
མཛེས་སྡུག་དང་བདེ་ཐང
བཟོ་རིག
རིག་གནས་དང་ལོ་རྒྱུས
དགའ་སྟོན
ཁོར་ཡུག
ཟས་དང་བཏུང་རྫས
ཕྱིར་འཕྲུལ་རིག
ཚན་རིག
རྩེད་འགྲན
རིག་རྩལ
གྱོན་རུང
Thin Brass Wire Drawn Through a Drawplate
Forge

བཟོས་མཁན

Forge

14. སྤྱི་ཟླ་བཅུ་པ 2026NO
༢
༠
༠
༠
༠

Thin Brass Wire Drawn Through a Drawplate

Thin brass wire is drawn from brass rod through the holes of a drawplate one size at a time, lubricated with beeswax and annealed whenever it stiffens. The volume stays the same, so the wire grows longer as it gets thinner. The picture: a small coil of brass wire.
བར་མ
Half a day

ལམ་སྟོན

1

Ready the rod

Take brass rod a little larger than the plate's largest hole, or hammer it down to that, and anneal it: heat to a dull red and quench.

གོམ་པ་འདིའི་རྫས་རིགས:

རག་གི་དབྱུག་པ།རག་གི་དབྱུག་པ།0.1 m
ཆུ།ཆུ།5 ལི་ཊར།

ལག་ཆས་དགོས་མཁོ:

མགར་བའི་རྡོ་ལེབ།མགར་བའི་རྡོ་ལེབ།
རྒྱབ་ཐིག་གི་ཐོ་བ།རྒྱབ་ཐིག་གི་ཐོ་བ།
པོ་རོ་པེན་གྱི་མེ་ལྕེ།པོ་རོ་པེན་གྱི་མེ་ལྕེ།
མགར་བའི་ལག་བཟུང་།མགར་བའི་ལག་བཟུང་།
སྲ་བཟོའི་ཆུ་སྣོད།སྲ་བཟོའི་ཆུ་སྣོད།
2

Taper the end

File the first 2 cm to a long taper so it pokes through the hole.

ལག་ཆས་དགོས་མཁོ:

དར་མའི་ཚོགས་ཆས།དར་མའི་ཚོགས་ཆས།
ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
3

Set up the plate

Clamp the drawplate in the vise, tapered side of the holes toward you, and rub beeswax on the rod.

གོམ་པ་འདིའི་རྫས་རིགས:

སྦྲང་ཞུན།སྦྲང་ཞུན།5 g

ལག་ཆས་དགོས་མཁོ:

ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།
ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
4

Draw

Push the taper through the first hole it will not slip through, grip it with the draw tongs and pull it through in one steady pull, straight out from the plate.

ལག་ཆས་དགོས་མཁོ:

འཐེན་ནིའི་ཀམ།འཐེན་ནིའི་ཀམ།
ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།
ཀོ་བའི་ལས་ལག་ཤུབས།ཀོ་བའི་ལས་ལག་ཤུབས།
5

Next holes, and anneal

Draw through each smaller hole in turn. When it gets stiff, coil it, anneal it to a dull red on a fire brick and quench.

ལག་ཆས་དགོས་མཁོ:

པོ་རོ་པེན་གྱི་མེ་ལྕེ།པོ་རོ་པེན་གྱི་མེ་ལྕེ།
མེ་ཐེག་སོ་ཕགམེ་ཐེག་སོ་ཕག
སྲ་བཟོའི་ཆུ་སྣོད།སྲ་བཟོའི་ཆུ་སྣོད།
6

Measure and coil

Stop at the size you need, measured with the caliper. Anneal it once more for soft wire and coil it.

ལག་ཆས་དགོས་མཁོ:

ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6
7

Length from the rod

Jupyter ཚང་དེབ་མངོན་གསལ་འབད་དོ་…

རྫས་རིགས

3
  • ས་ཆ་འཛིན
  • 5 ལི་ཊར།
    ས་ཆ་འཛིན
  • ས་ཆ་འཛིན

ལག་ཆས་དགོས་མཁོ

12

འབྲེལ་ཡོད་བིལུ་པིརིན་ཊི

བིལུ་པིརིན་ཊི་འདི་ཚུ་ཐབས་ལམ་དང་རྫས་རིགས། སྤྱི་ཆོས་བགོ་བཤའ་བྱེད

CC0 སྤྱི་དབང

བིལུ་པིརིན་ཊི་འདི་CC0 འོག་བཀྲམས་ཡོད། ཁྱེད་རང་གིས་ཆོག་མཆན་མ་བཞེས་པར་ཕབ་ལེན་དང་བཟོ་བཅོས། བགོ་བཤའ། དགོས་མཁོ་གང་ལའང་བཀོལ་སྤྱོད་བྱས་ཆོག

བཟོ་མཁན་ལ་རྒྱབ་སྐྱོར་བྱེད་པའི་ཆེད་ཁོང་ཚོའི་བིལུ་པིརིན་ཊི་བརྒྱུད་ཐོན་སྐྱེད་ཉོ། བཟོ་མཁན་གྱིས བཟོ་མཁན་གྱི་ཁེ་ཕོགས ཚོང་པས་གཏན་འཁེལ་བྱས་པ། ཡང་ན་བིལུ་པིརིན་ཊི་འདིའི་པར་གསར་བཟོས་ཏེ་ཁྱེད་རང་གི་བིལུ་པིརིན་ཊི་ནང་མཐུད་སྦྲེལ་བྱས་ཏེ་ཡོང་སྒོ་བགོ་བཤའ་བྱེད།

གྲོས་བསྡུར

(0)

ནང་འཛུལ གྲོས་བསྡུར་ནང་མཉམ་ཞུགས་ཆེད

བསམ་ཚུལ་ཚུ་ཐོབ་བཞིན...