合作

艺术

美容与健康

工艺

文化与历史

娱乐

环境

食品与饮料

逆向工程

科学

体育

技术

可穿戴设备

Cupola Furnace: the Common Foundry Cupola with a Drop Bottom (Bolland, 1893)

Simpson Bolland · Public domain (published 1893)

创建者

Forge

4. 十一月 2026

Cupola Furnace: the Common Foundry Cupola with a Drop Bottom (Bolland, 1893)

The founder's 'common cupola': an upright steel shell lined with firebrick, standing on four columns over a drop bottom, with a wind-box round it feeding the tuyeres and a charging door high up. Coke and pig iron go in at the top in layers; blast at the tuyeres melts the iron, which runs out at the spout. Variable: the inside diameter, 24 to 84 in, which sets height, tuyeres, blower and charges. Fig. 9's 36 in cupola is 12 ft to the charging hole and takes 840 lb coke and 2520 lb iron on the bed, then 302 lb coke and 2718 lb iron per charge. Source: S. Bolland, The Iron Founder Supplement (1893), pp. 34-54. Unknown: shell plate and brick sizes. Picture: Fig. 9 of the book.

专家

Unknown

说明

Size the cupola

Choose the inside diameter from the iron needed per hour: 10 tons in two hours (about 10,760 lb an hour) needs 48 in; 6 tons, 40 in. Make it tall enough that the gas burns before it escapes: a 50 in cupola is 14 ft from the base to the bottom of the charging hole, Fig. 9's 36 in one 12 ft. Above 60 in, keep 60 in at the tuyeres and widen above them, since the blast cannot reach the middle of a wider stock.

所需工具：

未知尺寸

Build the shell, columns and drop bottom

Build a steel shell with a charging hole and door, standing on four columns. Close the bottom with swing doors on a central prop, so the whole contents can be dropped at the end of a heat. Put a slag hole a little below the tuyeres and a spout at the bottom. Ours: mild steel plate, iron castings for the bottom doors. Not given: plate thickness.

此步骤所需材料：

低碳钢板1 shell, charging door

铸铁件1 drop-bottom doors

未知金属1 columns, prop, spout

所需工具：

电弧焊机

未知尺寸

Fit the tuyeres and wind-box

Ring the cupola with a wind-box feeding the tuyeres, with a main blast pipe sized from the table (good for runs up to 100 ft). Tuyere area grows with the diameter: a 24 in cupola needs the area of 1 1/2 round 6 in tuyeres (or two flat ones 10 1/2 x 2 in), a 60 in about 13 1/2 (or eight flat 16 1/2 x 3 in), an 84 in 31 (or sixteen flat 16 x 3 1/2 in). Never reduce the tuyere area. A 42 in cupola takes a No. 3 Root blower and a 6 h.p. engine.

此步骤所需材料：

低碳钢板1 wind-box

未知金属1 tuyeres, blast pipe

所需工具：

电弧焊机

鼓风机

Line it with firebrick

Line the shell with firebrick, every brick rubbed well down on the next and fitting the shell closely, set in mortar of the same nature as the bricks. A good lining lasts one to two years if the melter mends it each morning with thin coats of daubing, keeping its first shape. Ours: fireclay bricks and refractory clay mortar.

此步骤所需材料：

耐火黏土砖1 lining

耐火黏土砂浆1 setting and daubing

所需工具：

泥抹子

Make the bed and melt

Ram a sand bottom so it lies about 10 in below the tuyeres. Lay the fuel bed, about 22 in of coke above the tuyeres (840 lb in Fig. 9's 36 in cupola), and the first iron (2520 lb), then alternate charges of coke and iron (302 lb and 2718 lb). Blow: about 30,000 cubic feet of air melts a ton of iron. On long heats flux with white marble chips and draw the slag off at the slag hole. At the end, drop the bottom.

所需工具：