Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream
Daniel Deshon 2d of Somerset, Pennsylvania, received US 27,701, dated 3 April 1860, for a churn. A box of cream stands on curved rockers whose pegs sit in notches along the ways of a stand. Rocked by a handle, the box tips end to end and the cream runs through racks of rods; as the rockers roll, the point they rest on moves along with the weight, so little force is needed.
The patent gives no sizes; every size here is ours, and so is our reading of where the racks sit.
Fortgeschritten
About 2 days
Anweisungen
1
1
A fulcrum that walks
A fulcrum that walks
Jupyter-Notebook wird geladen …
2
2
Cream rushing end to end through pins, one month before
Cream rushing end to end through pins, one month before
Newbrough's barrel tips on a fixed pivot. Deshon's box rolls, so its pivot follows the cream.
3
3
Read US 27,701
Read US 27,701
"... this is done without contending but very little with the weight from the fact that the fulcrum at the bottom of the rockers (b) changes from one end to the other in accordance to the change of the weight inside of the vessel, always keeping in the center of the weight; consequently balancing the weight in its motion and saving most of the labor required to churn."
4
4
Vessel a and lid d
Vessel a and lid d
From 20 mm hardwood board make a box 600 x 250 mm inside and 290 deep; glue and screw it and seal the inside joints with silicone sealant. Cut a 150 mm opening across the middle of the top and a lid to fit it, with a hardwood block handle e.
Materialien für diesen Schritt:
Hartholzbrett3 Stück
Holzleim1 Stück
Holzschrauben40 Stück
Silikondichtmasse1 StückBenötigte Werkzeuge:
Tischkreissäge
Stichsäge
Akkubohrschrauber
Bohrersatz
Schraubzwinge mit Schiebebügel
Schraubendreher-Satz
Bandmaß (Rollmeter)5
5
Racks i
Racks i
Make two racks, each two hardwood side bars 24 x 20 mm, 355 long, with nine 10 mm stainless rods across between them. Stand them in the vessel leaning together, their feet on the floor 30 mm from the ends, meeting in the middle 240 mm above the floor.
Materialien für diesen Schritt:
Hartholzbrett1 Stück
Edelstahlstab2 StückHolzleim1 StückBenötigte Werkzeuge:
Tischkreissäge
Bügelsäge (Metallsäge)
Feilen (Handfeile)AkkubohrschrauberBohrersatz6
6
Rockers b with projections f, and handle c
Rockers b with projections f, and handle c
Draw an arc of 400 mm radius with the compass on two 20 mm hardwood boards and cut each rocker with that arc as its bottom, 48 degrees of arc (325 mm), rising to the box's top; leave one 140 mm taller and cut a hand-hole in it as the handle c. Bore seven 12 mm holes along each arc, 6 degrees apart, and glue in dowel pegs standing 8 mm out as the projections f. Bolt a rocker on each long side of the vessel, centred, the arc's lowest point 40 mm below the vessel's bottom.
Materialien für diesen Schritt:
Hartholzbrett2 Stück
Hartholzdübel1 StückHolzleim1 Stück
Schlossschraube4 Stück
Handflügelmutter4 StückBenötigte Werkzeuge:
KompassStichsäge
WinkelmesserAkkubohrschrauberBohrersatz
Flachfräsbohrer-Satz
Schleifpapier
Rollgabelschlüssel7
7
Pedestal h with ways and notches g
Pedestal h with ways and notches g
Cut two hardwood ways 520 x 120 x 30 mm and set them on edge under the rockers, 290 mm apart inside; join them with two cross boards near the floor. Cut seven notches 14 mm wide and 11 deep in each way's top edge, 41.9 mm apart from the middle, to match the pegs.
Materialien für diesen Schritt:
Hartholzbrett2 StückHolzleim1 StückHolzschrauben16 StückBenötigte Werkzeuge:
Tischkreissäge
Stechbeitelsatz für HolzAkkubohrschrauberBohrersatzSchraubzwinge mit SchiebebügelSchraubendreher-SatzBandmaß (Rollmeter)8
8
The build in 3D
The build in 3D
FreeCAD model of this build, tipped 10 degrees and cut through the middle: the vessel with its lid and the two racks leaning together, the rockers with their pegs in the ways' notches, and the pedestal.
9
9
Churn
Churn
Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel and close the lid. Push and pull the handle c steadily, tipping the vessel up to about 18 degrees each way, timing it. When the butter comes, lift the lid, take out the racks and the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materialien für diesen Schritt:
Schlagsahne10 l
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl10
10
Troubleshooting
Troubleshooting
Rolling-rocker churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Daniel Deshon 2d** of Somerset, Pennsylvania, US 27,701, 3 April 1860, "Churn". He claimed the racks, vessel, pedestal and rockers with projections in notched ways, combined. He places the racks only by dotted lines in his figure; our two racks leaning together are our reading of them. Every size here is ours.
Materialien
11- 3 StückPlatzhalter
- 4 StückPlatzhalter
- 56 StückPlatzhalter
- 1 StückPlatzhalter
- 2 StückPlatzhalter
- 1 StückPlatzhalter
- 4 StückPlatzhalter
- 4 StückPlatzhalter
- 10 lPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
19- 1 vendor sell this, none ship to you yetPlatzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
1Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Rocking Barrel Brake-Pin Churn: Cream Rushes End to End Through Rows of Pins, a Diagonal Board Gathers the Butter
von Buttercup
Holzbearbeitung
2
0
0
0
0
0
Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
von Buttercup
Holzbearbeitung
1
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
von TheChef
HANDWERK
60
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.