Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Twin-Crank Slide-Top Churn: Two Dashers on a Bent Crank Shaft, Sliding Plates Keep the Milk In
Cable L. Gilpatrick of Saco, Maine, received US 25,405, dated 13 September 1859, for a churn. A crank shaft bent into two opposite cranks rides on two posts above a box and works two dashers, so one goes down as the other comes up. Each dasher is two boards crossed and bored with holes. The staffs pass through holes in two slides that move in casings on the top, following the staffs so the milk cannot splash out.
The patent gives no sizes; every size here is ours.
Fortgeschritten
About 2 days, plus printing
Anweisungen
1
1
One up, one down
One up, one down
Jupyter-Notebook wird geladen …
2
2
Two dashers in one box, a few weeks before
Two dashers in one box, a few weeks before
Campbell rocked his two dashers on a lever. Gilpatrick drives his from a bent crank shaft and covers the top with slides.
3
3
Read US 25,405
Read US 25,405
"Motion is then communicated to the dashers by means of the crank-shaft. As one dasher descends, the other ascends. Thus the milk is kept in contant agitation, which is necessary in order to churn expeditiously. The slides being operated upon by the dasher-staffs prevents the milk from splashing out, as it otherwise would do."
4
4
Print the staff collars
Print the staff collars
Each collar is two halves round a crank pin: the lower half with a 30 mm square socket for the staff, and a cap; two M5 screws close them. Print two sets. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Box A and its posts
Box A and its posts
From 20 mm hardwood make a box 400 x 360 mm and 450 mm deep inside, with a bottom. Make the two 400 mm sides 170 mm taller, narrowed to posts 120 mm wide above the box, and bore each post 13 mm, 600 mm above the bottom's underside, for the shaft. Glue and screw a cleat 20 mm square along the inside of each post side, 30 mm below the rim, for the top. Fill the box with water overnight so it swells tight, then empty it.
Materialien für diesen Schritt:
Hartholzbrett3 Stück
Holzleim1 Stück
Holzschrauben30 StückBenötigte Werkzeuge:
Tischkreissäge
Handsäge
Akkubohrschrauber
Bohrersatz
Schraubzwinge mit Schiebebügel
Anschlagwinkel
Bandmaß (Rollmeter)
Wasser6
6
Crank shaft D and crank E
Crank shaft D and crank E
Cut 12 mm stainless rod about 750 mm long. Heat each bend red with the torch and bend it in the vise into two cranks of 50 mm throw, pointing opposite ways, each crank pin 50 mm long, their middles 180 mm apart. Check the journals line up by rolling the shaft on the bench. Thread one end through a post, the collars' lower halves onto the pins, and the other end through the other post. Fix a hardwood crank E, 160 mm long with a handle, on the end that sticks out.
Materialien für diesen Schritt:
Edelstahlstab1 StückHartholzbrett1 Stück
Hartholzdübel1 StückHolzleim1 StückBenötigte Werkzeuge:
Propanbrenner
Schraubstock
Hammer
Hitzebeständige Handschuhe
Bügelsäge (Metallsäge)
Feilen (Handfeile)AkkubohrschrauberBohrersatzBandmaß (Rollmeter)7
7
Top A', casings F and slides H
Top A', casings F and slides H
Cut the top to drop onto the cleats, with two slots 140 x 50 mm across it, under the cranks, and a finger hole. Over each slot build a casing F: two rails 20 x 26 mm, 370 mm long, 80 mm apart, with a strip on each that overhangs the inside by 8 mm, and an end block at each end, leaving 346 mm inside. Cut each slide H 240 x 79 mm from 18 mm hardwood, so it slides under the strips, with a hole 34 mm square in its middle, 4 mm bigger than the staff.
Materialien für diesen Schritt:
Hartholzbrett2 StückHolzleim1 StückHolzschrauben24 StückBenötigte Werkzeuge:
Tischkreissäge
Oberfräse
Lochbeitel
Holzhammer (Klüpfel)AkkubohrschrauberBohrersatz
SchleifpapierSchraubzwinge mit Schiebebügel8
8
Staffs B and dashers C
Staffs B and dashers C
Cut two staffs 30 mm square, 480 mm long. For each dasher, half-lap two boards 180 x 50 x 15 mm into a cross, bore eight 12 mm holes, cut a 30 mm square hole in the middle, and glue the staff's end into it. Set the top on its cleats, pass each staff up through its slide's hole, and bolt the collar's cap over its pin and onto the staff's top, turning the cross so its arms point to the box's corners.
Materialien für diesen Schritt:
Hartholzbrett1 StückHolzleim1 Stück
Maschinenschrauben4 Stück
Unterlegscheibe4 Stück
Sicherungsmutter mit Kunststoffeinsatz4 Stück
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-DruckerTischkreissägeLochbeitelHolzhammer (Klüpfel)AkkubohrschrauberBohrersatz
Schraubendreher-SatzSchleifpapier9
9
The build in 3D
The build in 3D
FreeCAD model of this build, one side and the lower part of one post cut away: the box, the bent crank shaft on its posts with crank E, the two staffs in their collars, the dashers, and the slides in their casings on the top. The crank was turned through 24 positions.
10
10
Churn
Churn
Lift the collars' caps off, take out the top, pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer, and put the top and caps back. Turn the crank steadily, timing it. When the butter comes, take the top out, lift out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materialien für diesen Schritt:
Schlagsahne15 l
Grobes Meersalz1 StückWasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus EdelstahlSchraubendreher-Satz11
11
Troubleshooting
Troubleshooting
Twin-crank churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Cable L. Gilpatrick** of Saco, Maine, US 25,405, 13 September 1859, "Churn". He claimed the crank shaft D and staffs B with the top A', "when said top is provided with boxes (F,) in which play slides, through which the staffs pass". The patent gives no sizes; every size here is ours. His collars are not described beyond "passing around said cranks"; ours are printed and split so the top can come out.
Materialien
12- 3 StückPlatzhalter
- 4 StückPlatzhalter
- 54 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 4 StückPlatzhalter
- 4 StückPlatzhalter
- Platzhalter
- 1 StückPlatzhalter
- 15 lPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
24- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
2Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
von Buttercup
Holzbearbeitung
1
0
0
0
0
0
Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
von Martin
Holzbearbeitung
2
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
von TheChef
HANDWERK
60
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.