Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Rotating-Receiver Stationary-Break Churn: The Whole Cream Vessel Turns, a Narrow Fixed Break Churns It
Mortimer S. Harsha of Sycamore, Illinois, received US 26,459, dated 13 December 1859, for what he called the "Vertical Rotating and Stationary Break Churn". Instead of a dasher, the whole cream vessel turns on an upright shaft with a pointed foot, driven by a gear and crank below it, while one narrow perforated break, fixed to a removable top, stands still near the vessel's side. The turning cream keeps going like a balance wheel, so little effort keeps it churning.
The patent gives no sizes; every size here is ours.
Fortgeschritten
About a day, plus printing
Anweisungen
1
1
The turning cream against a still break
The turning cream against a still break
Jupyter-Notebook wird geladen …
2
2
Fixed brakes in turning cream, three months before
Fixed brakes in turning cream, three months before
Taylor turned a dasher among fixed brakes. Harsha turns the vessel itself against a single fixed break.
3
3
Read US 26,459
Read US 26,459
"This is accomplished by said break presenting only a small resisting surface to the moving cream, while the cream being made to rapidly rotate on said vertical or upright shaft only against said break dash, becomes, along with its receiver, a receptacle of the power applied, similar to that of a balance wheel, and so by its own accumulative force, when power is once applied, puts it in motion"
4
4
Print the gear wheel G
Print the gear wheel G
Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a long hub bored 16.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the socket
Print the socket
A cup 50 mm across and 22 mm tall with a cone recess for the shaft's point. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the flange
Print the flange
A disc 200 mm across and 15 mm thick bored 16.6 mm, to carry the receiver. Print with 100 % infill. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Base E, brace H, posts F and top D
Base E, brace H, posts F and top D
Make a hardwood base 600 x 600 mm and screw the socket in its middle. Screw a brace H to it, an upright 30 x 40 mm with an arm reaching over the socket, bored 16.6 mm 25 to 55 mm up as the shaft's journal box. Tenon two posts 30 x 50 mm, 515 mm tall, into the base 490 mm apart, and make a top board 550 x 160 x 20 mm with mortises to drop onto their tenons so it lifts off. Set two chairs 44 x 30 mm, 124 mm tall, for the gear wheel's shaft.
Materialien für diesen Schritt:
Hartholzbrett3 Stück
Holzleim1 Stück
Holzschrauben20 Stück
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker
Tischkreissäge
Stichsäge
Lochbeitel
Holzhammer (Klüpfel)
Akkubohrschrauber
Bohrersatz
Schraubzwinge mit Schiebebügel
Bandmaß (Rollmeter)9
9
Shaft C, receiver A and gearing
Shaft C, receiver A and gearing
File one end of a 16 mm stainless shaft 170 mm long to a point. Pin the pinion and the flange on it, stand its point in the socket through the journal box, and bolt the stockpot's bottom to the flange with stainless screws sealed with silicone. Fit the crown wheel on a 12 mm stainless shaft through the chairs, meshing under the pinion, with a crank and handle on its end.
Materialien für diesen Schritt:
Edelstahlstab2 Stück
Suppentopf1 Stück
Maschinenschrauben4 Stück
Sicherungsmutter mit Kunststoffeinsatz4 Stück
Unterlegscheibe8 Stück
Silikondichtmasse1 Stück
Hartholzdübel1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)
Feilen (Handfeile)AkkubohrschrauberBohrersatz
Rollgabelschlüssel
Schraubendreher-Satz10
10
Break dash B
Break dash B
Cut a hardwood break 60 x 15 mm long enough to reach from the top board to 25 mm above the receiver's floor, bore ten 16 mm holes through it, and fix it by a tenon through the top board so it hangs 30 mm in from the receiver's side.
Materialien für diesen Schritt:
Hartholzbrett1 StückHolzleim1 StückBenötigte Werkzeuge:
Tischkreissäge
Flachfräsbohrer-SatzAkkubohrschrauberLochbeitelHolzhammer (Klüpfel)
Schleifpapier11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the receiver cut through the middle: the base with its socket, brace and posts, the shaft with pinion and flange, the crown wheel and crank, the turning receiver and the fixed perforated break hanging from the top.
12
12
Churn
Churn
Lift the top off, pour about 9 litres of heavy cream at about 15 °C into the receiver, checked with the thermometer, and put the top back. Turn the crank steadily, timing it: once the cream is moving it keeps going with little effort. When the butter comes, lift the top and break out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materialien für diesen Schritt:
Schlagsahne9 l
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl13
13
Troubleshooting
Troubleshooting
Rotating-receiver churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Mortimer S. Harsha** of Sycamore, DeKalb County, Illinois, assignor to himself, Rufus S. Sanborn and H. B. Jones, US 26,459, 13 December 1859, "Churn". He claimed: "An entirely stationary break dash in combination with a cream receiver, made to rotate on a vertical or upright shaft". His break is made "of such size as the relative size of the machine requires, and of any common form or shape"; the patent gives no sizes, and every size here is ours. His receiver was tin, zinc or wood; ours is a stainless stockpot.
Materialien
14- 3 StückPlatzhalter
- 2 StückPlatzhalter
- 20 StückPlatzhalter
- 1 StückPlatzhalter
- 2 StückPlatzhalter
- 1 StückPlatzhalter
- 4 StückPlatzhalter
- Platzhalter
- 8 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 9 lPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
19- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
5Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
von Buttercup
Holzbearbeitung
1
0
0
0
0
0
Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
von Buttercup
Holzbearbeitung
0
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
von TheChef
HANDWERK
60
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.