KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
GRÜNE ZUKUNFT
REVERSE ENGINEERING
School Projects
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
Karen

Erstellt von

Karen

2. Juli 2026SE
1
0
0
0
0

Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes

The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
Fortgeschritten
8

Anweisungen

1

Harvest and clean long rye straw

Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel

Benötigte Werkzeuge:

KnifeKnife
2

Split and soak the binding cane

Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.

Materialien für diesen Schritt:

Split CaneSplit Cane1 Bündel
WaterWater3 Liter

Benötigte Werkzeuge:

KnifeKnife
3

Make the girth gauge

Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.

Benötigte Werkzeuge:

Skep Girth GaugeSkep Girth Gauge
4

Bind the crown

Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel
Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
5

Feed straw into an even rope

Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel

Benötigte Werkzeuge:

Skep Girth GaugeSkep Girth Gauge
6

Sew the first coils to the crown

Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.

Materialien für diesen Schritt:

Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
7

Spiral outward to start the dome

Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel
Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
8

Build the domed wall downward

Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel
Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
Skep Girth GaugeSkep Girth Gauge
9

Keep the courses even

Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel

Benötigte Werkzeuge:

AwlAwl
10

Widen to the finished base

As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.

Materialien für diesen Schritt:

Rye StrawRye Straw1 Bündel
Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
11

Cut the flight entrance

At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.

Benötigte Werkzeuge:

KnifeKnife
12

Finish and lock the base coil

Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.

Materialien für diesen Schritt:

Split CaneSplit Cane1 Meter

Benötigte Werkzeuge:

AwlAwl
13

Trim the skep clean

Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.

Benötigte Werkzeuge:

KnifeKnife
14

Clom the outside for weatherproofing

Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.

Materialien für diesen Schritt:

Cow DungCow Dung2 kg
Ball ClayBall Clay1 kg
15

Cure the finished skep

Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.

Materialien

6

Benötigte Werkzeuge

3

Materialien verbundener Blueprints

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Verwandte Blueprints

Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien

Building a Thatched Lean-To Shelter — Basic Wind and Rain Protectionvon Spartan
Egyptian Beeswax Candle — Making Beeswax Candles with Rush Wicksvon YourGrandma
Honey as a Wound Dressing — The Oldest Antimicrobial Medicine Known to Humanityvon Bob

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Making a Sistrum — The Sacred Rattle of Ancient Egypt
Saving Lettuce Seeds — Letting the Leaf Crop Bolt
Making a Leather Sling — The Shepherd's Projectile Weaponsurvival
Making a Clay Crucible for Smelting — The Vessel That Holds Molten MetalMetalworking
Making a Bronze Awl — The Leatherworker's Piercing ToolMetalworking
Making a Fire-Hardened Hunting Spear — The Oldest Weaponsurvival

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...