Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
Jehu Mitchell of Aleppo township, Pennsylvania, received US 27,927, dated 17 April 1860, for a churn. The dasher hangs from above in a long journal box on a standard fixed to the lid, with no step or metal bearing in the tub, whose "oxidation ... imparts a bad flavor to the butter". One half of the box is a cap hinged at one side: lift out half the lid, unhook the cap and the dasher comes out with the gearing left in place.
The patent gives no sizes; every size here is ours.
Fortgeschritten
About 2 days, plus printing
Anweisungen
1
1
Held from above
Held from above
Jupyter-Notebook wird geladen …
2
2
A crank-turned upright dasher, one week before
A crank-turned upright dasher, one week before
Lynch's shaft stands in a step on the bottom. Mitchell hangs his from above, with nothing in the tub.
3
3
Read US 27,927
Read US 27,927
"Suspending the dasher within an elongated hinged journal box in the manner described, combined the following advantages. A rigid bearing is afforded to the dasher so as to prevent any tremulous motion, without the necessity of any metallic step or bearing within the churn, the oxidation of which imparts a bad flavor to the butter."
4
4
Print the driving wheel E
Print the driving wheel E
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion M
Print the pinion M
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Lid B and C, brakes O
Lid B and C, brakes O
Cut a hardwood lid 15 mm thick to sit on the bucket's rim and saw it in two across the middle: part C carries the standard, part B lifts out. Cut a 28 mm half-hole in the middle of the cut edge for the shaft and a 30 mm hole in B to look in. Screw three hardwood brakes O, 30 mm deep and 245 tall, to the bucket's side a third of a turn apart, and seal the screw holes outside with silicone.
Materialien für diesen Schritt:
20-Liter-Eimer1 Stück
Hartholzbrett2 Stück
Holzschrauben6 Stück
Silikondichtmasse1 StückBenötigte Werkzeuge:
Stichsäge
Tischkreissäge
Flachfräsbohrer-Satz
Akkubohrschrauber
Bohrersatz
Schraubendreher-Satz
Bandmaß (Rollmeter)7
7
Standard D, journal box and cap G
Standard D, journal box and cap G
Glue up a hardwood standard 60 mm wide and 66 deep, 111 mm tall above the lid, with its back 22 mm rising to 217 mm and bored 12.6 mm across near the top for the wheel's axle. Mortise it into lid part C behind the shaft's hole. Cut a cap G 60 x 30 mm, 111 tall, and bore a 25.2 mm hole down the joint between standard and cap, half in each. Hang the cap on a butt hinge at one side and fit a hook H and eye I on the other.
Materialien für diesen Schritt:
Hartholzbrett1 Stück
Holzleim1 Stück
Möbel-Scharnier (Aufschraubband)1 Stück
Haken und Öse1 StückHolzschrauben4 StückBenötigte Werkzeuge:
Tischkreissäge
Stechbeitelsatz für Holz
Schraubzwinge mit SchiebebügelAkkubohrschrauberBohrersatzFlachfräsbohrer-SatzSchraubendreher-Satz8
8
Dasher J with wings N and collars K and L
Dasher J with wings N and collars K and L
Cut a 25 mm hardwood dowel 485 mm long and glue a 12 mm stainless spindle into its top, standing 56 mm out. Glue two hardwood wings 200 x 60 x 20 mm across it, 20 and 140 mm above its foot, each bored with two 24 mm holes. Fit a hardwood collar L 44 mm across just below the lid, and a collar K 40 mm across on the spindle resting on the box's top. Set the shaft in the box, close the cap, and key the pinion M on the spindle above K.
Materialien für diesen Schritt:
Hartholzdübel2 StückHartholzbrett1 Stück
Edelstahlstab1 StückHolzleim1 Stück
Hartholzblock1 Stück
Shaft Collar1 Stück
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-DruckerTischkreissägeFlachfräsbohrer-SatzAkkubohrschrauberBohrersatz
Bügelsäge (Metallsäge)
Feilen (Handfeile)
Schleifpapier9
9
Driving wheel E and crank
Driving wheel E and crank
Pass a 12 mm stainless axle through the standard's back, fit the wheel E on it meshing the pinion, and a hardwood crank with a dowel handle on the other end; hold it with a collar and split pin.
Materialien für diesen Schritt:
Edelstahlstab1 StückHartholzbrett1 StückHartholzdübel1 StückHolzleim1 StückShaft Collar1 Stück
Splint1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)Feilen (Handfeile)AkkubohrschrauberBohrersatz
Schraubstock10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the dasher J with its two wings hanging from the journal box, the brakes O, the lid, the standard D with its hinged cap G, hook and eye, and the wheel E with pinion M.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the lid and dasher in place, and turn the crank steadily, timing it. To look at the butter, lift out lid part B. When the butter comes, lift part B out, unhook the cap and take the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materialien für diesen Schritt:
Schlagsahne8 l
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl12
12
Troubleshooting
Troubleshooting
Hung-dasher churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Jehu Mitchell** of Aleppo township, Greene County, Pennsylvania, US 27,927, 17 April 1860, "Churn". He did not claim a churn without a bottom step nor a hinged bearing alone, but the gearing, standard, hinged cap, dasher and collar together. His journal box runs higher; ours stops below the crown wheel. His wings and brakes are "of common construction"; our two wings and three brakes, and every size, are ours.
Materialien
16- 1 StückPlatzhalter
- 2 StückPlatzhalter
- 10 StückPlatzhalter
- 1 StückPlatzhalter
- 3 StückPlatzhalter
- Platzhalter
- 1 StückPlatzhalter
- 2 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 8 lPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
18- 1 vendor sell this, none ship to you yetPlatzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
3Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Leaning-Scoop Churn: Three Scoops Tilted 10, 5 and 0 Degrees Throw the Cream at Sharp-Topped Ribs and a Slit Cover
von Buttercup
Holzbearbeitung
1
0
0
0
0
0
Floating-Breaker Churn: A Propeller Dasher Under a Breaker That Floats in Wall Grooves, a Water Tube Held by the Faucet
von Buttercup
Holzbearbeitung
0
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
von TheChef
HANDWERK
60
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.