KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Piston-Pump Egg Beater: Pump the Eggs Through a Grate
A whisk stirs the eggs; it does not force them through anything.
J. J. Parker of Marietta, Ohio, received US 25,038, dated 9 August 1859, for an egg beater and churn combined: a tin tube with square openings at its lower end and a piston inside, worked up and down "in the manner of a pump" by a crank, which "draws the eggs in and out through the grate bars until they are completely torn in pieces or made perfectly fine and frothy"; a band turned round the tube's foot closes the openings to vary the agitation.
This rung works out the jet speed at each band setting, then prints the tube, band and piston, fits the crank, and times a beating at two settings.
Fortgeschritten
About 3 hours, plus printing
Anweisungen
1
1
Jet speed at each setting
Jet speed at each setting
Jupyter-Notebook wird geladen …
2
2
The churning it also does
The churning it also does
The embedded blueprint churns cream to butter. Parker's pump-tube does the same when worked longer in cream.
3
3
Read US 25,038
Read US 25,038
"At the lower end of the tube is a band of about one half an inch in width loosely fitted with openings one fourth of an inch square and corresponding exactly with the openings in the tube and of the same size, so that by turning the band around either way the openings are closed or made smaller at pleasure, so as to produce more or less agitation in the eggs or cream. This band has a bottom with grate like bars cut or made in it."
4
4
Print the tube, band and piston
Print the tube, band and piston
Print the tube, the band with its grate and the piston disk. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Materialien für diesen Schritt:
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker5
5
Print the tube
6
6
Print the band
7
7
Print the piston
Print the piston
The piston, printed as step 4 describes.
8
8
Pack the piston
Pack the piston
Cut a leather disk 2 mm larger than the piston. Clamp it between the printed disk and a washer on an M3 rod end with a nut, so its edge seals the tube.
Materialien für diesen Schritt:
Leder1 Stück
Unterlegscheibe1 Stück
Sechskantmutter1 Stück
Maschinenschrauben1 StückBenötigte Werkzeuge:
Bastelmesser
Rollgabelschlüssel
Digitaler Messschieber 6 Zoll9
9
Post and crank
Post and crank
Epoxy a 4 mm wire post up the tube's side, bent at its top into bearings 100 mm above the tube. Bend a crank shaft of 3 mm wire with a 22 mm crank one end and a handle the other, and link the crank to the rod with a wire pitman.
Materialien für diesen Schritt:
Rundstahl (Baustahl)1 Stück
Edelstahldraht1 Stück
Zweikomponentenepoxid1 StückBenötigte Werkzeuge:
Schraubstock
Rundzange
Flachzange
Bügelsäge (Metallsäge)
Klare Schutzbrille10
10
The patent drawing
The patent drawing
US 25,038 drawing sheet, public domain (expired patent).
11
11
Beat at two settings
Beat at two settings
Stand the beater in a bowl with two eggs and a spoon of sugar. Crank twice a second with the band fully open and time to a fine froth; repeat with the band half closed.
Materialien für diesen Schritt:
Ei4 Stück
Kristallzucker1 StückBenötigte Werkzeuge:
Große Rührschüssel aus Edelstahl
Stoppuhr12
12
A pump that leaks past, sticks or splashes
A pump that leaks past, sticks or splashes
Piston-pump egg beater troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**J. J. Parker** of Marietta, Ohio, received US 25,038, dated 9 August 1859. His smaller machine's tube is one and a half inches across and one and five eighths deep; the crank shaft is No. 7 wire with a seven-eighths-inch crank; the piston is two oval pieces of thin metal with leather between, its edges forced out by pressing them together. It may also be worked by a handle on the rod instead of a crank.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed PETG stands in for tin. The notebook treats the flow as steady. Your times are the result.
Materialien
10- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 4 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
11- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
3Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.