KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES

The Gas Turbine: When the Turbine Finally Beat Its Own Compressor
Compress air, burn fuel in it, and expand the hot gas through a turbine that also turns the compressor. The idea is simple and old. Making it work took until 1903, when the Norwegian engineer Ægidius Elling ran the first gas turbine that delivered more power than its own compressor consumed.
The difficulty is arithmetic. The compressor takes most of what the turbine makes, so small losses in either machine wipe out the net output entirely. It needed efficient compressors and turbine metal that could stand red heat — and the Whittle turbojet in this catalogue is the result.
This rung works out the arithmetic, then demonstrates it safely with an air turbine and a compressor on the bench.
Fortgeschritten
About 3 hours
Anweisungen
1
1
Net work: turbine minus compressor
Net work: turbine minus compressor
Jupyter-Notebook wird geladen …
2
2
Demonstrate the energy bill with compressed air
Demonstrate the energy bill with compressed air
No combustion here. Print a small impulse air turbine — a 60 mm wheel with 20 cupped buckets — on the shaft of a hobby motor used as a generator, with a 330 Ω load and the multimeter across it. Blow it with the air compressor through the regulator and a nozzle made from a short piece of tube.
Measure the electrical power out (V² ÷ R). Then measure the power the compressor draws from the wall while it runs — the clamp meter on the live conductor, times the mains voltage.
The turbine returns a tiny fraction of what the compressor took. That is the gas turbine's problem without the fuel: compression is expensive, and only by adding heat between compressor and turbine does the turbine get back more than it cost.
Materialien für diesen Schritt:
PETG-Filament30 g
Hobby Motor - Gear1 Stück
330-Ohm-Widerstand1 Stück
Klarer Vinylschlauch0.5 MeterBenötigte Werkzeuge:
Luftkompressor (Pancake-Bauart)
Druckminderer
Multimeter
Stromzange AC/DC 600 A
FDM-3D-Drucker
Klare Schutzbrille
Gehörschutz3
3
History and context
History and context
**Ægidius Elling, Norway, 1903** — the first gas turbine to deliver net power — more than its own compressor consumed. No patent number is asserted here, and the details of his machine are left to the sources; the principle is the payload. Earlier attempts had failed exactly as the notebook predicts: the compressor ate all the turbine's output.
The line runs through Büchi's turbocharger (the next rung) — a gas turbine driving a compressor, fed by an engine's exhaust — to the Whittle turbojet and the power-station gas turbine.
**Honest limits.** Efficiency depends on turbine inlet temperature, which is limited by materials and cooling; small gas turbines are inefficient; and part-load efficiency falls away. **Do not build a combustion gas turbine**: the parts spin at speeds where a failure is a shrapnel event, and the combustor is a blowtorch.
Materialien
4- 30 gPlatzhalter
- Hobby Motor - Gear10% Provision1 Stück€2.21
- 1 StückPlatzhalter
- 0.5 MeterPlatzhalter
Benötigte Werkzeuge
7- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Gehörschutz10% ProvisionPlatzhalter
Geschätzte Gesamtkosten
Was der Maker gekauft hat. Materialien ohne Preis besorgst du dort, wo du sie kaufst.
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien

Parsons Steam Turbine
von Martin
Physik
40
0
0
0
0
0

The Heat of Compression: Why Compressed Air Is Hot and Wet
von Martin
Mechanik
11
0
0
0
0
0

The Screw Compressor: A Built-In Ratio, and the Cost of the Wrong One
von Martin
Mechanik
8
0
0
0
0
0

The Rotary Regenerator: Store Heat in a Wheel and Carry It Across
von Martin
Mechanik
11
0
0
0
0
0

The Sirocco Fan: Many Shallow Forward-Curved Blades
von Emma
Mechanik
9
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.