KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
The Hooded Fountain Paint Brush: A Dome Shares the Paint Between Both Sides
Paint fed into the middle of a brush clogs its head, and one side of the bristles runs dry.
Franklin E. Fornwalt of Harrisburg, Pennsylvania, received US 842,644, patented 29 January 1907, for a fountain brush "for applying paint": a tin holder clamped over the brush carries a reservoir whose floor has a row of apertures under a hollow turning valve, and below it a hood whose dome sends equal paint to both sides of the bristles.
This rung works out the flow a brush needs, then folds the holder from aluminium sheet over a 120 mm brush and measures the paint it lays on each side of a stroke.
Fortgeschritten
About 5 hours
Anweisungen
1
1
Paint the brush needs
Paint the brush needs
Jupyter-Notebook wird geladen …
2
2
A turned perforated tube before it
A turned perforated tube before it
The embedded blueprint turns a perforated tube to change how water leaves a brush. Fornwalt turns a perforated valve to open or close a row of holes over a hood.
3
3
Read US 842,644
Read US 842,644
"In virtue of the provision of the said hood D paint is effectually prevented from getting on the brush-head b, and at the same time liability of the brush becoming choked and impaired is reduced to a minimum. It will also be apparent that the hood D conveys an equal quantity of paint to each side of the body of bristles a and assures the paint reaching the sides of the body of bristles in the form of thin layers, which obviously contributes materially to the efficiency of the fountain-brush as a whole."
4
4
Fold the tank
Fold the tank
Fold aluminium sheet into a box 160 × 60 × 70 mm with a lid. Rivet the seams and seal them inside with silicone. Cut a 25 mm filling hole in the lid.
Materialien für diesen Schritt:
Aluminiumblech1 Stück
Blindnieten1 Stück
Silikondichtmasse1 StückBenötigte Werkzeuge:
Blechschere
Flachzange
Schraubstock
Blindnietzangen-Set
Akkubohrschrauber
Bohrersatz
Lochsägen-Set
Lederarbeitshandschuhe5
5
Drill the floor
Drill the floor
Drill six 3 mm holes along the floor's centre line, 20 mm apart.
Benötigte Werkzeuge:
AkkubohrschrauberBohrersatz
Permanentmarker
Lineal6
6
Make the turning valve
Make the turning valve
Cut 200 mm of 10 mm copper tube. Drill six 3 mm holes in a line to match the floor's, and file a 6 mm slot along the opposite side. Pass it through both end walls just above the floor and bend one end into a crank.
Materialien für diesen Schritt:
Kupferrohr1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)AkkubohrschrauberBohrersatz
Feilen (Handfeile)Schraubstock7
7
Fold the hood
Fold the hood
Bend an aluminium strip into a ridge with 40° sides and rivet it under the floor, its peak under the holes.
Materialien für diesen Schritt:
Aluminiumblech1 StückBlindnieten1 StückBenötigte Werkzeuge:
SchraubstockBlindnietzangen-Set8
8
Clamp on the brush
Clamp on the brush
Rivet two side skirts below the tank. Drill them and a 120 mm brush's stock for two M6 bolts, and clamp the brush between the skirts with nuts so their lower edges rest on the bristles.
Materialien für diesen Schritt:
Sechskantschrauben-Sortiment1 Stück
Sechskantmutter1 Stück
Unterlegscheibe1 StückBlindnieten1 StückBenötigte Werkzeuge:
AkkubohrschrauberBohrersatz
Rollgabelschlüssel
Pinselset9
9
The patent drawing
The patent drawing
US 842,644 drawing sheet, public domain (expired patent).
10
10
Paint and weigh
Paint and weigh
Fill the tank with thinned acrylic paint. Weigh a plywood board, open the valve half, and paint one 1 m stroke each way. Weigh it again; compare how wet each side of the bristles is.
Materialien für diesen Schritt:
Acrylfarben-Set1 Stück
Wasser1 Stück
Sperrholzplatte1 StückBenötigte Werkzeuge:
Digitale Küchenwaage
Bandmaß (Rollmeter)
Stoppuhr11
11
A brush that clogs, floods or paints one side
A brush that clogs, floods or paints one side
Hooded fountain paint brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Franklin E. Fornwalt** of Harrisburg, Pennsylvania, filed US 842,644 on 28 September 1906; it was patented 29 January 1907. His holder is preferably tin; bolts through the brush head with thumb nuts press the side walls in against the bristles, and removing them lets the brush be replaced. A connection may take a hose from a paint supply or compressed air. A right-angled form paints vertical surfaces, feeding the upper side of the bristles only.
**Honest limits.** Riveted aluminium stands in for his tin, and plain nuts for his thumb nuts. Your weights are the result.
Materialien
10- 1 StückPlatzhalter
- 3 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
17- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak
von YourGrandma
Mechanik
36
0
0
0
0
0
Making Hide Glue Distemper — The Traditional Ceiling and Wall Paint of Europe
von Charlie
KUNST
69
0
0
0
4
0
The Long-Handled Fountain Brush: A Ring of Holes Wets the Bristles From the Ground
von Martin
Mechanik
29
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.