Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES

Woven Harvesting Basket: the Square Willow Basket with Bow Handle (Hasluck, 1903)
A sturdy square willow basket with a rope-wrapped bow handle over the open top, for carrying and gathering: the basket-maker's 'grocer's square basket'. Bottom 17 x 11 in, sides 11 in deep to the wale, corner sticks, a foot rim and a handle about 20 in high.
Source: Paul N. Hasluck, Basket Work of All Kinds (1903), pp. 27-47. Picture: Figs. 48-51 of the book.
Erfahren
Unknown
Anweisungen
1
1
Weave the bottom in the screw-block
Weave the bottom in the screw-block
Wet the sticks an hour ahead. Cut six sticks 20 in long (3 in extra for the block), the two outside ones thicker. Set the outside pair 11 in apart in the screw-block, the four inside evenly between, thick and thin ends alternating (Fig. 33). Start with two osiers worked together, then weave one rod at a time, butts behind odd sticks, checking the 11 in width with a bent gauge rod and tapping the weave close with the iron, to 17 in long. Lock the end with one long rod (Fig. 34), take it out and pick off the ends.
Materialien für diesen Schritt:
Dickere Weidenruten6 20 in
Weidenrute1 weaversBenötigte Werkzeuge:
Wasser
Schere (groß)
Einhand-Gartenschere
Hammer
Flaches Holzbrett2
2
Stake up and fit corner sticks
Stake up and fit corner sticks
Point seventeen pairs of stakes, about half as thick as the sticks: ten for each side, seven for each end. Push the end stakes in beside the sticks; for the sides open holes through the outside sticks with the bodkin. Bend each stake up with the picking knife and gather them in a small hoop (Fig. 35). Cut four corner sticks as thick as the outside bottom sticks, flat-cut at the foot (Fig. 37).
Materialien für diesen Schritt:
Weidenstecklinge34 17 pairs
Dickere Weidenruten4 corner sticksBenötigte Werkzeuge:
Durchziehnadel
Einhand-Gartenschere
Hammer3
3
Upset and rand the sides
Upset and rand the sides
Upset with three rods (four if there will be no foot rim), working the corner sticks in at each corner (Figs. 38-39), and add a second round. Rand with rods drawn in their lengths, each butt one stake on from the last, to about 10 in deep, keeping the sides upright and true. Leave a space between the two middle stakes of each side the full depth for the handle. Put strainers across when the middle stakes come out of the hoop, and level the weaving at about 9 in.
Materialien für diesen Schritt:
Weidenrute1 upsetting, randingBenötigte Werkzeuge:
Hammer
Durchziehnadel4
4
Wale, border and pick
Wale, border and pick
Work a wale of four rods, each behind two stakes and in front of two (Fig. 43), using eight rods, to 11 in deep. Lay the stakes down into the border and finish by cramming (Figs. 45-47). Pick every butt and top inside and out so the outside is smooth.
Materialien für diesen Schritt:
Weidenrute8 waleBenötigte Werkzeuge:
Einhand-Gartenschere
Hammer5
5
Add the foot rim
Add the foot rim
Turn the basket over, push a rim stake in beside each stake and each corner stick, upset once round with six rods, tap down and border 'inside two and outside three' (Fig. 49).
Materialien für diesen Schritt:
Weidenstecklinge1 rim stakes
Weidenrute6 upsettingBenötigte Werkzeuge:
Durchziehnadel
Hammer6
6
Fit and wrap the bow handle
Fit and wrap the bow handle
Bend a thick, well-soaked stick into a bow (Fig. 48), push its ends down the handle spaces to the upsetting, about 8 to 9 in above the border (some 20 in from the bottom to the underside of the bow), and shoulder it with the knee. Wrap it with four long smooth osiers, each twisted rope-fashion and lapped round the bow and through under the wale (Figs. 50-51).
Materialien für diesen Schritt:
Dickere Weidenruten1 bow
Weidenrute4 handle wrapBenötigte Werkzeuge:
Wasser
Durchziehnadel
Einhand-GartenschereMaterialien
3- 1 bowPlatzhalter
- 4 handle wrapPlatzhalter
- 1 rim stakesPlatzhalter
Materialien verbundener Blueprints
Dieser Bauplan stellt her
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.


