ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Adjustable-Float Annular Dasher Churn: Floats on a Ring Set More or Less Oblique
Goodrich Lightfoot of Elgin, Illinois, received US 16,210, dated 9 December 1856, for an annular plate on the shaft's foot carrying floats above and below, each on a bolt through its centre, "turned more or less angularly or obliquely so as to present a greater or less resisting surface to the cream."
This rung prints the plate, floats and gears, builds the churn and makes butter.
Intermedio
About 3 hours, plus printing
Instrucciones
1
1
Setting the floats
Setting the floats
Cargando el cuaderno de Jupyter…
2
2
Adjustable resistance before it
Adjustable resistance before it
Gore turns fixed pins in the wall; Lightfoot sets floats on the turning ring.
3
3
Read US 16,210
Read US 16,210
"The plate A, has floats or buckets b, c, attached to its upper and lower surface, by bolts or screws d, which pass through their centers. These floats or buckets may be turned more or less angularly or obliquely so as to present a greater or less resisting surface to the cream, as desired, and consequently the cream may be subjected to a greater or less degree of agitation—as desired."
4
4
Print the parts
Print the parts
Print the annular plate, eight floats, the step, the crown wheel, the pinion and the standard. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materiales para este paso:
Filamento PETG1 piezaHerramientas necesarias:
Impresora 3D de filamento (FDM)5
5
Print the annular plate
Print the annular plate
The annular plate, printed as step 4 describes.
6
6
Print the float
Print the float
The float, printed as step 4 describes.
7
7
Print the step
8
8
Print the crown wheel
Print the crown wheel
The crown wheel, printed as step 4 describes.
9
9
Print the pinion
Print the pinion
The pinion, printed as step 4 describes.
10
10
Print the standard
Print the standard
The standard, printed as step 4 describes.
11
11
Plate and floats
Plate and floats
Bolt a float above and below the plate at each of its four holes with a stainless M4 screw and nut, snug enough to hold the angle you set. Push the plate onto a 10 mm square hardwood shaft standing in the step, in a square food-grade container about 200 mm across.
Materiales para este paso:
Tornillos de máquina1 pieza
Tuerca hexagonal1 pieza
Espigas de madera dura1 pieza
Recipiente de almacenaje de grado alimentario1 piezaHerramientas necesarias:
Juego de destornilladores
Llave inglesa ajustable12
12
Lid, gears and crank
Lid, gears and crank
Fix half the lid with a hole for the shaft, the pinion on the shaft's top and the standard with the crown wheel meshing it; screw a dowel handle into the wheel.
Materiales para este paso:
Redondo de acero dulce1 piezaEspigas de madera dura1 pieza
Tornillo para madera n.º 8 x 1"1 piezaHerramientas necesarias:
Juego de destornilladores
Taladro inalámbrico13
13
The build in 3D
The build in 3D
FreeCAD model of this build: the box cut away to show the annular plate with floats above and below, set oblique, the shaft on its step, and the crown wheel and pinion.
14
14
Set the floats and churn
Set the floats and churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Set the floats oblique for thin cream, more square for more agitation, and crank steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materiales para este paso:
Crema de leche espesa2000 ml
Sal marina gruesa1 pieza
Agua1 piezaHerramientas necesarias:
Termómetro de sonda permanente
Cronómetro
Báscula digital de cocina
Bol grande de acero inoxidable15
15
Troubleshooting
Troubleshooting
Adjustable-float churn troubleshooting.
Flow
Loading...
16
16
History and honest limits
History and honest limits
**Goodrich Lightfoot** of Elgin, Kane County, Illinois, US 16,210, 9 December 1856. The specification letters both the box and the annular plate A. He claimed the adjustable floats on the annular plate secured to the shaft. A container, printed parts and a crown wheel with a pinion stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn.
Materiales
10- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 2000 mlMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
8- Marcador de posición
- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
7Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
Adjustable-Pin Resistance Churn: Flat-Ended Pins Turned From Outside Set the Churn's Grip
por Martin
COMIDA Y BEBIDAS
36
0
0
0
0
0
Stopped Auxiliary Dasher Churn: A Loose Dasher Held Still by a Stop, One Turning Below It
por Millie
COMIDA Y BEBIDAS
31
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANÍA
54
0
0
0
0
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.