Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter.
Result: a boring bar, plus the small short-cut bar of Fig. 110.
Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
Intermedio
Unknown
Instrucciones
1
1
Turn the bar
Turn the bar
Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.
Materiales para este paso:
Barra redonda de acero dulce1 boring barHerramientas necesarias:
Torno de metal
Dimensiones desconocidas2
2
Fit the cutter and set screw
Fit the cutter and set screw
Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.
Materiales para este paso:
Barra cuadrada de acero para herramientas1 cutter
Metal desconocido1 set screwHerramientas necesarias:
Taladro de columna
Juego de machos y terrajas
Piedra de afilar de rueda
Horno de tratamiento térmico
Cubo de temple3
3
Bore with it
Bore with it
Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.
Herramientas necesarias:
Torno de metal
Tornillo de carruajeMateriales
3- 1 boring barMarcador de posición
- Marcador de posición
- 1 set screwMarcador de posición
Herramientas requeridas
8- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Materiales de Blueprints conectados

10% de atribución
Mild Steel Bar Stock Forged from an Ingot
por Forge
Moderno
44
0
0
0
5
0

10% de atribución
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
por Forge
Herrero
32
0
0
0
5
0

10% de atribución
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
por Forge
Herramientas para Metalurgia
12
0
0
0
1
0
Este plano hace
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.
