ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere
Beaten in an open bowl, egg spatters and the air is not forced into it.
James M. Jay of Canton, Ohio, received US 27,054, dated 7 February 1860, for an egg beater whose case is a hollow globe of two halves hinged and caught together; a horizontal shaft through it carries concentric rings, the outer one close to the inside so it sweeps the bottom, turned by a wheel and gear on a stand. "The air which occupies the upper part ... is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs."
This rung works out the air-to-egg ratio, then prints the ring dasher and gears, closes it in two bowls, and times a beating.
Intermedio
About 5 hours, plus printing
Instrucciones
1
1
Air shut in with the eggs
Air shut in with the eggs
Cargando el cuaderno de Jupyter…
2
2
A dasher in a closed box before it
A dasher in a closed box before it
The embedded blueprint spins a dasher in a square box. Jay shuts the eggs in a globe so the air is driven into them.
3
3
Read US 27,054
Read US 27,054
"In my egg beater the air which occupies the upper part of the hollow bottom B, together with that which fills the cover or cap C, is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs by the rings or dashes H', while the eggs are carried up and through the air in the cap or case C, so that a perfect mixture of the air and eggs is effected."
4
4
Print the rings and gears
Print the rings and gears
Print the concentric-ring dasher, the 36-tooth wheel and the 12-tooth gear. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Materiales para este paso:
Filamento PETG1 piezaHerramientas necesarias:
Impresora 3D de filamento (FDM)5
5
Print the concentric-ring dasher
Print the concentric-ring dasher
The concentric-ring dasher, printed as step 4 describes.
6
6
Print the 36-tooth wheel
Print the 36-tooth wheel
The 36-tooth wheel, printed as step 4 describes.
7
7
Print the 12-tooth gear
Print the 12-tooth gear
The 12-tooth gear, printed as step 4 describes.
8
8
Make the globe
Make the globe
Take two matching bowls 120 mm across from the set. Drill both rims at opposite points for the shaft, 5.5 mm, so the shaft lies on the joint.
Herramientas necesarias:
Taladro inalámbrico
Juego de brocas
Calibre digital de 6 pulgadas
Juego de cuencos para mezclar9
9
Shaft, rings and stand
Shaft, rings and stand
Pass a 5 mm rod through one bowl's holes and the dasher's hub, and epoxy the hub at the centre. Epoxy the 12-tooth gear on the rod outside. Mount the 36-tooth wheel with a crank on an M5 screw on a hardwood upright so it meshes, and stand the lower bowl in a plywood ring.
Materiales para este paso:
Redondo de acero dulce1 pieza
Epoxi de dos componentes1 pieza
Bloque de madera dura1 pieza
Tablero contrachapado1 pieza
Tornillos de máquina1 pieza
Arandela plana1 pieza
Tuerca hexagonal1 pieza
Tornillo para madera n.º 8 x 1"1 piezaHerramientas necesarias:
Sierra para metales
Segueta (sierra de marquetería)Taladro inalámbricoJuego de brocas
Llave inglesa ajustable
Juego de destornilladores10
10
The patent drawing
The patent drawing
US 27,054 drawing sheet, public domain (expired patent).
11
11
Closed against open
Closed against open
Beat two egg whites with the top bowl clamped on and time them to stiff peaks; then again with the top off. Compare the times and the volume of foam.
Materiales para este paso:
Huevo4 piezasHerramientas necesarias:
Cronómetro
Báscula digital de cocina12
12
A globe that leaks, rings that scrape
A globe that leaks, rings that scrape
Closed-globe egg beater troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**James M. Jay** of Canton, Ohio, assignor to himself and John Danner, received US 27,054, dated 7 February 1860. The halves are turned to break joints and fit tight; a hook on the cover hangs on a pivot between lugs, and a swinging catch holds the cover down; the shaft's bearings are in the lower half's edge, the cover cut to fit over them. He wrote that it does not matter whether one or more eggs are beaten.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Two bought bowls stand in for his turned halves, without a hinge. Your times are the result.
Materiales
10- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 4 piezasMarcador de posición
Herramientas requeridas
11- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
3Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.