ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box
A beater spun in a round bowl soon drags the whole mixture round with it.
Thomas McBean of Fowlerville, New York, received US 24,134, dated 24 May 1859, for an egg beater: "a double spiral-shaped beater or dasher with its surface formed into steps within a square box," turned horizontally on a vertical shaft by a bevel pinion and a handle, so that the dasher and the square box together "so thoroughly breaks up all portions of the eggs that they may be well and very thoroughly beaten in a few seconds."
This rung compares the side and corner gaps, then prints the stepped dasher, builds a square box with a bevel drive, and times beating in the box against a round bowl.
Intermedio
About 4 hours, plus printing
Instrucciones
1
1
Tip speed and the corners
Tip speed and the corners
Cargando el cuaderno de Jupyter…
2
2
A geared beater a month before it
A geared beater a month before it
The embedded blueprint beats with two wire whisks turning opposite ways. McBean turns one stepped dasher and lets the box's corners do the breaking up.
3
3
Read US 24,134
Read US 24,134
"The nature of my invention consists in arranging a double spiral-shaped beater or dasher with its surface formed into steps within a square box and in communicating to this dasher a swift rotary motion so as to revolve it horizontally within said box."
4
4
Print the dasher
Print the dasher
Print the stepped double-spiral dasher. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Materiales para este paso:
Filamento PETG1 piezaHerramientas necesarias:
Impresora 3D de filamento (FDM)5
5
Print the dasher
Print the dasher
The dasher, printed as step 4 describes.
6
6
Build the box
Build the box
Cut a plywood base and four sides to make a box 104 mm square inside and 90 mm deep. Glue and screw it, and seal the inside seams with silicone.
Materiales para este paso:
Tablero contrachapado1 pieza
Tornillo para madera n.º 8 x 1"1 pieza
Sellador de silicona1 piezaHerramientas necesarias:
Segueta (sierra de marquetería)
Taladro inalámbrico
Juego de brocas
Juego de destornilladores
Regla7
7
Fit the shaft and gears
Fit the shaft and gears
Screw a hardwood bar across the box's top with a bracket above it. Run a 5 mm rod down through the bar to a socket in the floor, with the dasher at its foot and one bevel gear at its top; mount the other gear on a crank shaft through the bracket so they mesh.
Materiales para este paso:
Bloque de madera dura1 pieza
Redondo de acero dulce1 pieza
Juego de engranajes cónicos (acero, 1:1)1 pieza
Epoxi de dos componentes1 pieza
Arandela plana1 piezaHerramientas necesarias:
Sierra para metalesTaladro inalámbricoJuego de brocas
Tornillo de banco8
8
The patent drawing
The patent drawing
US 24,134 drawing sheet, public domain (expired patent).
9
9
Square box against round bowl
Square box against round bowl
Beat two egg whites in the box at about two crank turns a second and time them to stiff peaks. Repeat with the dasher in a round bowl of the same size.
Materiales para este paso:
Huevo4 piezasHerramientas necesarias:
Bol grande de acero inoxidable
Cronómetro10
10
A dasher that swirls, scrapes or slips
A dasher that swirls, scrapes or slips
Stepped spiral egg beater troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Thomas McBean** of Fowlerville, Livingston County, New York, received US 24,134, dated 24 May 1859. The dasher's spiral circular plates are soldered to a small tube and bent into steps radial from the axis; the shaft passes up through the box's cover to a bracket, its lower end resting on a pin in the box's bottom. He claimed the double spiral dasher in combination with the square box.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A printed dasher and a bought 1:1 bevel pair stand in for his tin plates and pinions. Your times are the result.
Materiales
10- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 4 piezasMarcador de posición
Herramientas requeridas
10- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
1Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.