Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
Forge

Creado por

Forge

14. noviembre 2026NO
6
0
0
0
0

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)

The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
Intermedio
Two to three days of building

Instrucciones

1

His sizes

Cargando el cuaderno de Jupyter…
2

Read Edwinson

"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3

Build the base

Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.

Materiales para este paso:

Bloque de piedraBloque de piedra1 pieza
Aro de hierroAro de hierro1 pieza
Arcilla refractariaArcilla refractaria1 pieza

Herramientas necesarias:

Paleta de albañilPaleta de albañil
Nivel de burbujaNivel de burbuja
4

Make the fire back and tuyere

Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)

Materiales para este paso:

Granalla de hierro (lastre)Granalla de hierro (lastre)1 pieza
Placa de hierroPlaca de hierro1 pieza
Surtido de tornillos hexagonalesSurtido de tornillos hexagonales1 pieza

Herramientas necesarias:

Taladro de columnaTaladro de columna
Fragua de herreroFragua de herrero
MartilloMartillo
5

Firebrick top and back

Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).

Materiales para este paso:

Ladrillos refractariosLadrillos refractarios1 pieza
Arcilla refractariaArcilla refractaria1 pieza
Aro de hierroAro de hierro1 pieza

Herramientas necesarias:

Paleta de albañilPaleta de albañil
Nivel de burbujaNivel de burbuja
6

Fit the slake trough

Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.

Materiales para este paso:

Chapa de acero dulceChapa de acero dulce1 pieza
Remaches de hierroRemaches de hierro1 pieza
AguaAgua1 pieza

Herramientas necesarias:

Taladro de columnaTaladro de columna
MartilloMartillo
7

Bind with the rim

Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.

Materiales para este paso:

Placa de hierroPlaca de hierro1 pieza
Surtido de tornillos hexagonalesSurtido de tornillos hexagonales1 pieza

Herramientas necesarias:

Fragua de herreroFragua de herrero
YunqueYunque
MartilloMartillo
Taladro de columnaTaladro de columna
8

Connect the blast

Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.

Herramientas necesarias:

Soplador de aireSoplador de aire
9

Lay the floor

Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.

Materiales para este paso:

Cemento portlandCemento portland1 pieza
AguaAgua1 pieza

Herramientas necesarias:

MartilloMartillo
10

Troubleshooting

Hearth troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.

Materiales

11

Herramientas requeridas

7

Este plano hace

Blueprints relacionados

Estos blueprints comparten conocimiento — técnicas, materiales o principios

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...