ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

Fermenter Lid with Airlock Seat, 3D Printed in PETG
A snap-on lid that turns a small food-grade pail into a fermenter. It follows L. P. Beadle's 1980 US patent 4,218,964: an off-centre tapered hole that matches the airlock stem's taper, a triangular rim set in a groove so it flexes round the stem, stiffening rings, and a snap-fit edge. You measure your pail's rim and make the file for it. All sizes are ours, and we have not printed or tested it yet.
Principiante
About 10 hours, mostly printing
Instrucciones
1
1
Lid size, stem depth and gas force
Lid size, stem depth and gas force
Cargando el cuaderno de Jupyter…
2
2
Read US 4,218,964
Read US 4,218,964
"The stem support structure 30 includes a tapered hole the depth and slope of which are adapted to conform to the taper of stem 26 and to provide a resilient, gripping action ... annular rim portion 35 is defined by depressed circular groove 36 which provides the annular rim 35 with a type of hinge action." He put the hole off centre so the lid would not crack. The picture is our section.

3
3
Measure the pail
Measure the pail
Use a food-grade plastic pail with a rim lip all round. Measure the lip's outside diameter, and from the pail's top edge to the underside of the lip.
Herramientas necesarias:
Calibre digital de 6 pulgadas
Cubo de fermentación4
4
Make the lid for your pail
Make the lid for your pail
Run it in FreeCAD with your two measurements: OUT=. LIP_D= LIP_H= freecadcmd build_all.py
build_all.pypython
Herramientas necesarias:
Ordenador de sobremesa
Software CAD5
5
Print the lid
Print the lid
Print it top face down on the bed, no supports: the skirt and stiffening rings grow upwards. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls. The file here is for a 180 mm lip.
Materiales para este paso:
Filamento PETG125 gHerramientas necesarias:
Impresora 3D de filamento (FDM)
Juego de boquillas para impresora 3D6
6
Fit the airlock
Fit the airlock
Push the airlock's stem down into the hole by hand until it wedges, about 30 mm for our airlock. Do not force it further.
Herramientas necesarias:
Válvula de fermentación7
7
Leak test
Leak test
Fill the airlock to its line with water. Snap the lid on the empty pail. Press the middle of the lid gently: gas must bubble through the airlock, with no hiss at the rim or stem.
Herramientas necesarias:
Cubo de fermentación
Válvula de fermentación
Agua8
8
Sanitise
Sanitise
Wipe or soak the lid in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.
Herramientas necesarias:
Desinfectante
Agua9
9
Close the fermenter
Close the fermenter
Start the bead under the lip at one side and press the lid down all round until it snaps on.
Herramientas necesarias:
Cubo de fermentación10
10
Troubleshooting
Troubleshooting
Lid problems and fixes.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Leigh P. Beadle**, US 4,218,964, filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His lids were moulded in flexible plastic, and he noted that drilling a plain hole in the middle of a lid led to cracks and to gas escaping round the stem. He gives no sizes. Ours: every size, PETG, the bead and the fit to a measured pail. One change: his rim rises above the lid's top; ours stands in a recess with its top level with the lid, so the lid prints flat. PETG is stiffer than his plastic, so the grip comes more from the matched taper than from the rim. Checked in CAD; not yet printed or brewed with by us.
Materiales
1- 125 gMarcador de posición
Herramientas requeridas
9- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
1Materiales de Blueprints conectados
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.




