Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
John R. Grundy · Public domain
Forge

Creado por

Forge

13. noviembre 2026NO
0
0
0
0
0

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)

John R. Grundy of Philadelphia received US 860,369, dated 16 July 1907, for a two-part collar held by a single screw, where earlier split collars needed two. The screw passes through one pair of ends, an overhang on one part lying over the other. At the opposite side a tongue on one part fits a recess in the other. Both of those ends reach round the shaft past the diameter under the screw. When the screw's point presses the shaft, they hook under it and cannot open. Each part goes onto the shaft from the side, so the shaft stays in its bearings. We cut the two parts from a turned brass ring with a piercing saw, from a full-size template. The patent gives no sizes; every size here is ours.
Avanzado
About 2 days

Instrucciones

1

Why the hooks hold

Cargando el cuaderno de Jupyter…
2

Read US 860,369

"It is obvious that by using the single screw in place of a plurality of screws, as has hitherto been considered necessary, I am enabled to reduce the cost of the collar." "The parts of said collar are placed in position on the shaft by being moved toward it in radial planes."
3

Turn the ring

Grip 45 mm brass round bar in the 3-jaw chuck. Face it, turn it to 40 mm for 20 mm, centre-drill, drill through 15 mm and ream 16 mm. Part off 16 mm long and face the parted side.

Materiales para este paso:

Barra redonda de latónBarra redonda de latón1 pieza

Herramientas necesarias:

Torno de metalTorno de metal
Plato de torno de 3 mordazasPlato de torno de 3 mordazas
Herramienta de corte para tornoHerramienta de corte para torno
Juego de brocas de centrarJuego de brocas de centrar
Juego de brocasJuego de brocas
EscariadorEscariador
Gubia de tronzarGubia de tronzar
Calibre digital de 6 pulgadasCalibre digital de 6 pulgadas
Gafas de seguridadGafas de seguridad
4

Print the cutting template

Full-size A4 template: the end view of the ring with the outlines of parts B and B', and the bottom of the ring seen from below with the tongue b' and cheeks a'. Print at 100 %; its 50 mm bar must measure 50 mm.
Archivo de DisenoPDFCC0 - Free
Descargar modelo
5

Cut the parts apart

Glue the end view on one end face of the ring, centred, and the strip on the outside at the bottom. Wax the blade. Top joint: hold the ring in soft jaws, face up, and saw with the blade along the axis: in from the outside 5 mm left of the line to 14 mm radius, round the 14 mm circle to the line, and down the line into the bore. Bottom joint: turn the ring over and saw with the blade across the wall, following the strip from one end face to the other: the cheeks a' 3 mm left of the line, the tongue b' 3 mm right of it. Go slowly at the corners; the two parts come apart.

Herramientas necesarias:

Impresora de inyección de tintaImpresora de inyección de tinta
ColaCola
Tornillo de bancoTornillo de banco
Mordazas blandas para tornillo de bancoMordazas blandas para tornillo de banco
Sierra de joyeroSierra de joyero
Cera de abejaCera de abeja
6

Fit the joints and cut away the bores

File the saw marks off the joints until the tongue slides into its recess and the overhang lies on the other part, with the two parts round a 16 mm bar. File each part's bore out to 18 mm across over the 22 degrees next to the top joint on its own side, B' to the left of the line and B to the right, as the template shows. Try them on the bar: put B on from below right, then B' from below left, sliding it up under the overhang and the tongue into its recess. File until each goes on without forcing.

Herramientas necesarias:

Barra redonda de acero dulceBarra redonda de acero dulce
Tornillo de bancoTornillo de banco
Mordazas blandas para tornillo de bancoMordazas blandas para tornillo de banco
Juego de limasJuego de limas
Juego de limas de agujaJuego de limas de aguja
Calibre digital de 6 pulgadasCalibre digital de 6 pulgadas
7

Drill and tap for the screw

With both parts on the bar, the overhang lying on B', clamp the bar in the machine vice so the dashed screw line on the template stands upright. Drill 4.2 mm through the overhang and through B' into the bore, and tap M5 through both with cutting oil. Take the parts off and deburr the bore.

Materiales para este paso:

Aceite de corteAceite de corte1 pieza

Herramientas necesarias:

Barra redonda de acero dulceBarra redonda de acero dulce
Taladro de columnaTaladro de columna
Mordaza de máquinaMordaza de máquina
Juego de brocasJuego de brocas
Juego de machos y terrajasJuego de machos y terrajas
Volvedor de machosVolvedor de machos
DesbarbadorDesbarbador
8

The collar in 3D

FreeCAD model, our sizes: parts B and B' on a 16 mm shaft, the overhang b and the M5 screw at the top, the tongue b' between the cheeks a' at the bottom, and the bores cut away beside the top joint.
Archivo de DisenoSTLCC0 - Free
Descargar modelo
9

Fit it on the shaft

Run an M5 x 12 cup point set screw into the overhang until it just shows. Put B onto the shaft from the side where the collar is wanted, then B' from the other side, its top under the overhang and its tongue into the recess. Tighten the screw with the hex key: it pushes on the shaft and draws both bottom ends down against it. Try to slide and turn the collar; it must not move.

Materiales para este paso:

Prisionero de punta cóncavaPrisionero de punta cóncava1 pieza

Herramientas necesarias:

Juego de llaves AllenJuego de llaves Allen
10

Troubleshooting

Grundy collar troubleshooting.

Flow

Loading...
11

History and honest limits

**John R. Grundy** of Philadelphia, US 860,369, dated 16 July 1907, filed 28 January 1907. He claimed "a shaft collar made in two parts, and means for holding the parts together comprising a single screw passing through two adjacent ends of said two parts, the other ends of said parts being formed to co-act with the shaft to prevent their separation". His screw end also has a second projection b2 in a recess, holding the parts in line along the shaft; ours leaves it out, as the screw through both parts does that. His screw has a hex head; ours is a socket set screw. He gives no material; ours is brass, which a piercing saw cuts well. The patent gives no sizes; every size here is ours.

Materiales

3

Herramientas requeridas

24

Archivos de diseño

2

Este plano hace

Thumbnail
Marcador

Shaft Collar

Free

5
0
1

Blueprints relacionados

Estos blueprints comparten conocimiento — técnicas, materiales o principios

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)

por ForgeNO

Trabajo en Metal

0
0
0
0
0
0
Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)

Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)

por ForgeNO

Trabajo en Metal

0
0
0
0
0
0

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...