ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Side-Knife Can Opener: Round Holes and Long Ones With One Tool
A circular opener makes round holes only, too small for a flat sardine box.
F. S. Wyman of Chicago received US 80,326, dated 28 July 1868, for a side knife rigidly attached to the adjustable plate of a circular can opener, "by means of which square and longitudinal openings may be made in fruit-cans with the same tool which is used to make round holes": a slotted plate with a pointed pivot, and a plate sliding in the slot carrying both the circular knife and the side knife, fixed by a set screw.
This rung compares round and long openings, then builds the plate, pivot and both knives and cuts each kind.
Intermedio
About 3 hours
Instrucciones
1
1
Round against long
Round against long
Cargando el cuaderno de Jupyter…
2
2
A circular opener before it
A circular opener before it
The embedded blueprint cuts round holes about a spike. Wyman adds a side knife to the sliding plate for straight cuts.
3
3
Read US 80,326
Read US 80,326
"A represents a slotted plate, fitted in a handle, B, and having a pointed pivot, E, used as an axis for the knife D, the same as in the patent of S. D. Lecompte, of September 19, 1865, and has a plate, F, arranged to run in the slot B' and support the knife D, held in place by a set-screw, H, when moved in said slot to suit the semi-diameter of the opening to be made."
4
4
Make the slotted plate
Make the slotted plate
Cut 120 mm of 25 × 3 mm flat bar. Saw and file a 5 mm slot 70 mm long in it, starting 20 mm from one end.
Materiales para este paso:
Pletina de acero dulce1 piezaHerramientas necesarias:
Sierra para metales
Tornillo de banco
Taladro inalámbrico
Juego de brocas
Juego de limas de aguja
Regla5
5
Fit the pivot
Fit the pivot
Drill the plate's end 5 mm. File an M5 screw to a sharp point and fix it there with a nut, point down.
Materiales para este paso:
Tornillos de máquina1 pieza
Tuerca hexagonal1 piezaHerramientas necesarias:
Taladro inalámbricoJuego de brocas
Limas (lima de mano)
Llave inglesa ajustable6
6
Make the sliding plate and knives
Make the sliding plate and knives
Cut a 30 × 22 mm plate of flat bar. Cut a pointed circular knife and a straight side knife from 1 mm sheet; epoxy the first under its centre and the second along its side so it lies close to the slotted plate's edge.
Materiales para este paso:
Pletina de acero dulce1 pieza
Chapa de acero dulce1 pieza
Epoxi de dos componentes1 piezaHerramientas necesarias:
Sierra para metales
Tijeras de chapaLimas (lima de mano)
Piedra de afilar
Gafas de seguridad transparentes7
7
Set screw and handle
Set screw and handle
Drill the sliding plate for an M5 screw through the slot with a washer and nut. Fit a hardwood handle with epoxy.
Materiales para este paso:
Tornillos de máquina1 pieza
Arandela plana1 piezaTuerca hexagonal1 pieza
Espigas de madera dura1 piezaEpoxi de dos componentes1 piezaHerramientas necesarias:
Taladro inalámbricoJuego de brocasLlave inglesa ajustable8
8
The patent drawing
The patent drawing
US 80,326 drawing sheet, public domain (expired patent).
9
9
Cut a round and a long opening
Cut a round and a long opening
Cut a round hole in one sealed can about the pivot. On a second, cut four straight sides with the side knife, rocking the handle along each; time both and measure the openings.
Materiales para este paso:
Lata1 piezaHerramientas necesarias:
Cronómetro
Calibre digital de 6 pulgadas
Guantes de trabajo de cuero10
10
Knives that slip, bind or wander
Knives that slip, bind or wander
Side-knife can opener troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**F. S. Wyman** of Chicago received US 80,326, dated 28 July 1868. The plate and side knife should be one piece of steel, with a nib guiding it in the slot, the knife tempered to hold an edge. He did not claim the circular opener, patented by S. D. Lecompte on 19 September 1865, nor the side knife broadly, a similar device having been patented by S. P. Chapin on 17 July 1866; he claimed the side knife rigidly attached to the adjustable plate.
**Honest limits.** Epoxy stands in for his one-piece steel plate and knife, and nothing is tempered. Your times are the result.
Materiales
8- 1 piezaMarcador de posición
- 2 piezasMarcador de posición
- 2 piezasMarcador de posición
- 1 piezaMarcador de posición
- 2 piezasMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
14- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
The Pivot-Point Can Opener: A Spike at the Centre, a Blade Set to the Size
por Martin
COMIDA Y BEBIDAS
30
0
0
0
0
0
The One-Piece Sheet Can Opener: Point and Blade Struck From the Blank
por Mary
COMIDA Y BEBIDAS
35
0
0
0
0
0
The Shouldered-Blade Can Opener: The Shoulders Are the Fulcrum
por Forge
Trabajo en Metal
31
0
0
0
0
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.