Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

Creado por

Bubbles

14. noviembre 2026IT
4
0
0
0
0

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
Avanzado
An hour once the basic operations are mastered

Instrucciones

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

Materiales para este paso:

Tubo de vidrioTubo de vidrio1 pieza

Herramientas necesarias:

Mechero BunsenMechero Bunsen
Caña de soplador de vidrioCaña de soplador de vidrio
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

Materiales para este paso:

Tubo de vidrioTubo de vidrio1 pieza

Herramientas necesarias:

Limas (lima de mano)Limas (lima de mano)
Mechero BunsenMechero Bunsen
Caña de soplador de vidrioCaña de soplador de vidrio
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

Herramientas necesarias:

Mechero BunsenMechero Bunsen
Caña de soplador de vidrioCaña de soplador de vidrio
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

Herramientas necesarias:

Mechero BunsenMechero Bunsen
Caña de soplador de vidrioCaña de soplador de vidrio
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

Materiales para este paso:

Tubo de vidrioTubo de vidrio1 pieza

Herramientas necesarias:

Limas (lima de mano)Limas (lima de mano)
Mechero BunsenMechero Bunsen
Caña de soplador de vidrioCaña de soplador de vidrio
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

Materiales

1

Herramientas requeridas

3

Este plano hace

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...