ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours.
The picture: steel sewing needles (Wikimedia Commons).
Intermedio
Half a day
Instrucciones
1
1
Cut, soften and straighten
Cut, soften and straighten
Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.
Materiales para este paso:
Cuerda de piano70 mmHerramientas necesarias:
Alicates de corte
Fragua de herrero
Alicates de punta fina
Yunque2
2
Point
Point
Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.
Herramientas necesarias:
Juego de limas
Tornillo de banco
Gafas de seguridad3
3
Flatten and pierce the eye
Flatten and pierce the eye
Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.
Herramientas necesarias:
Yunque
Martillo de peña transversal
Taladro de mano
Juego de limas
Tornillo de banco
Gafas de seguridad4
4
Harden in oil
Harden in oil
Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.
Herramientas necesarias:
Fragua de herrero
Alicates de punta fina
Cubeta de temple con aceite
Gafas de seguridad5
5
Temper
Temper
Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.
Herramientas necesarias:
Horno de tratamiento térmico
Termopar con indicador
Yunque
Martillo de peña transversal6
6
Scour and polish
Scour and polish
Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.
Herramientas necesarias:
Tela de esmeril
Aceite de oliva
Jabón
Serrín
Asentador de cuero
Juego de limasMateriales
1- 70 mmMarcador de posición
Herramientas requeridas
17- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.


