ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush
Woody

Creado por

Woody

6. octubre 2026NO
32
0
0
0
0

The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush

An oil can and a rag spill, and a brush dipped in oil drips. Preston H. Clingan of Florence, Colorado, received US 787,278, dated 11 April 1905, for "a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof": an open thimble hangs from the can's mouth to near its bottom, a rolled burlap wick inside it is frayed above the mouth into a brush, and oil in the chamber round the thimble reaches the wick from underneath. This rung works out how high a wick can lift oil, then builds the can from a jar, a tin and burlap and weighs the oil it lays on a board.
Principiante
About 2 hours

Instrucciones

1

How high the wick lifts

Cargando el cuaderno de Jupyter…
2

A wick that feeds oil before it

The embedded blueprint feeds oil to a bearing through a wick. Clingan turns the wick's frayed end into the brush.
3

Read US 787,278

"My object is to provide a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof. The can includes a wick of absorbent material, which is constantly supplied with oil or other fluid within the can."
4

Make the thimble

Remove both ends of a tin can that passes through the jar's mouth with 6 mm to spare. Cut it 10 mm shorter than the jar's inside height. File the cut edges.

Materiales para este paso:

LataLata1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
Limas (lima de mano)Limas (lima de mano)
ReglaRegla
Guantes de trabajo de cueroGuantes de trabajo de cuero
5

Cut the lip ring

Cut an aluminium ring: outside to fit inside the jar's mouth, inside to fit round the thimble. Drill it 3 mm for a filling screw.

Materiales para este paso:

Chapa de aluminioChapa de aluminio1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
Taladro inalámbricoTaladro inalámbrico
Juego de brocasJuego de brocas
Limas (lima de mano)Limas (lima de mano)
6

Fix the thimble

Epoxy the ring round the thimble's top and into the jar's mouth, the thimble hanging 10 mm clear of the floor. Cut a rubber washer for the filling screw.

Materiales para este paso:

Tarro de vidrioTarro de vidrio1 pieza
Epoxi de dos componentesEpoxi de dos componentes1 pieza
Tornillos de máquinaTornillos de máquina1 pieza
Plancha de cauchoPlancha de caucho1 pieza

Herramientas necesarias:

Cúter de precisiónCúter de precisión
Juego de destornilladoresJuego de destornilladores
7

Roll the wick

Roll a strip of burlap tightly until it fills the thimble, 15 mm longer than it. Push it in and fray the top 15 mm with the fingers.

Materiales para este paso:

ArpilleraArpillera1 pieza

Herramientas necesarias:

TijerasTijeras
ReglaRegla
8

The build in 3D

FreeCAD model of this build, not of the patent: a 90 mm jar with a 66 mm mouth, the aluminium lip ring and filling screw, a 53 mm thimble 10 mm off the floor, the burlap wick with its frayed top, and the lid.
Archivo de DisenoBLENDCC0 - Free
9

Oil a board and weigh it

Pour linseed oil through the filling hole to half the jar's height and wait until the wick's top darkens. Weigh a plywood board, brush it once over, and weigh it again. Turn the closed jar on its side over a rag for a minute.
Paso 9 - Image 1

Materiales para este paso:

Aceite de linaza cocidoAceite de linaza cocido1 pieza
Tablero contrachapadoTablero contrachapado1 pieza
Trapos de algodónTrapos de algodón1 pieza

Herramientas necesarias:

Báscula digital de cocinaBáscula digital de cocina
CronómetroCronómetro
Cinta métricaCinta métrica
10

A wick that stays dry, floods or leaks

Oil-wick fountain brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Preston H. Clingan** of Florence, Colorado, assignor of one-half to John H. Todd of Cañon City, filed US 787,278 on 28 July 1904; it is dated 11 April 1905. His can is cylindrical with both ends contracted and threaded, so the cover fits either end; the thimble is soldered to an inward lip at the mouth; the wick is preferably a roll of burlap. He named oiling or polishing surfaces and cleaning windows among its uses. **Honest limits.** A jar with one threaded mouth stands in for his can. The notebook assumes a fully wetting wick and one pore size. Your weights are the result.

Materiales

10

Herramientas requeridas

12

Archivos de diseño

1

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...