Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Forge

Creado por

Forge

4. noviembre 2026NO
8
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
Intermedio
Unknown

Instrucciones

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 body, bottom
Alambre de hierroAlambre de hierro1 edge
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
EstacaEstaca
Mazo de maderaMazo de madera
Soldador eléctricoSoldador eléctrico
FundenteFundente
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 spout, stay
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
EstacaEstaca
Soldador eléctricoSoldador eléctrico
FundenteFundente
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 rose
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 pieza

Herramientas necesarias:

Compás de puntasCompás de puntas
Tijeras de chapaTijeras de chapa
EstacaEstaca
Martillo de aplanarMartillo de aplanar
Punzón (lezna)Punzón (lezna)
Bloque de madera duraBloque de madera dura
Soldador eléctricoSoldador eléctrico
FundenteFundente
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 top, handles, studs
Alambre de hierroAlambre de hierro1 No. 12 B.W.G.
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
Martillo de aplanarMartillo de aplanar
Cincel de aceroCincel de acero
Soldador eléctricoSoldador eléctrico
FundenteFundente
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

Materiales para este paso:

Pintura al óleoPintura al óleo2 coats

Herramientas necesarias:

TrementinaTrementina
Carbonato de calcio (blanco de España)Carbonato de calcio (blanco de España)

Materiales

4

Herramientas requeridas

12

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...