Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
Forge

Creado por

Forge

15. noviembre 2026NO
5
0
0
0
0

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)

C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
Intermedio
A day

Instrucciones

1

The steps

Cargando el cuaderno de Jupyter…
2

Read Willey

"A very efficient, quick-opening and closing vise for the drill-press table."
3

Make the bed

Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.

Materiales para este paso:

Pletina de acero dulcePletina de acero dulce1 pieza

Herramientas necesarias:

Sierra para metalesSierra para metales
GraneteGranete
Taladro de columnaTaladro de columna
Juego de brocasJuego de brocas
4

Make the end supports

Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.

Materiales para este paso:

Pletina de acero dulcePletina de acero dulce1 pieza
Surtido de tornillos hexagonalesSurtido de tornillos hexagonales1 pieza

Herramientas necesarias:

Sierra para metalesSierra para metales
Taladro de columnaTaladro de columna
Juego de brocasJuego de brocas
Limas (lima de mano)Limas (lima de mano)
5

Make the fixed jaw

Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.

Materiales para este paso:

Pletina de acero dulcePletina de acero dulce1 pieza
Redondo de acero dulceRedondo de acero dulce1 pieza

Herramientas necesarias:

Sierra para metalesSierra para metales
Limas (lima de mano)Limas (lima de mano)
Taladro de columnaTaladro de columna
Juego de brocasJuego de brocas
Martillo de bolaMartillo de bola
6

Make the sliding jaw

Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.

Materiales para este paso:

Pletina de acero dulcePletina de acero dulce1 pieza
Redondo de acero dulceRedondo de acero dulce1 pieza

Herramientas necesarias:

Sierra para metalesSierra para metales
Limas (lima de mano)Limas (lima de mano)
Taladro de columnaTaladro de columna
Juego de brocasJuego de brocas
Martillo de bolaMartillo de bola
Tornillo de bancoTornillo de banco
7

Make the cam

Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.

Materiales para este paso:

Eje de aceroEje de acero1 pieza
Redondo de acero dulceRedondo de acero dulce1 pieza

Herramientas necesarias:

Sierra para metalesSierra para metales
Taladro de columnaTaladro de columna
Juego de brocasJuego de brocas
Martillo de bolaMartillo de bola
8

Use it

Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.

Materiales para este paso:

Surtido de tornillos hexagonalesSurtido de tornillos hexagonales1 pieza

Herramientas necesarias:

Taladro de columnaTaladro de columna
9

Troubleshooting

Drill vise troubleshooting.

Flow

Loading...
10

History and honest limits

From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.

Materiales

4

Herramientas requeridas

7

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...