Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
Woody

Créé par

Woody

13. novembre 2026NO
9
0
0
0
0

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)

A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
Débutant
About 3 hours

Consignes

1

His sizes in centimetres

Chargement du notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3

Cut the staff and loop

Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.

Matériaux pour cette étape :

Perches de bambouPerches de bambou1 pièce
Cuir de harnaisCuir de harnais1 pièce
Rivets en cuivreRivets en cuivre1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Couteau à cuirCouteau à cuir
Chignole à mainChignole à main
MarteauMarteau
Mètre rubanMètre ruban
4

Make and fix the snow disk

Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Vernis à la gomme laqueVernis à la gomme laque1 pièce
Fil de ferFil de fer1 pièce
Cavalier en fil de ferCavalier en fil de fer4 pièces

Outils nécessaires :

Scie à chantournerScie à chantourner
Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
Pince platePince plate
MarteauMarteau
Brosse largeBrosse large
5

Set the spike

Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Fil de ferFil de fer1 pièce
Lingot de plombLingot de plomb1 pièce
Ficelle de juteFicelle de jute1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Chignole à mainChignole à main
Ciseaux à boisCiseaux à bois
Louche en métalLouche en métal
Chalumeau à propaneChalumeau à propane
Limes (lime à main)Limes (lime à main)
Pince platePince plate
6

Troubleshooting

Ski staff troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.

Matériaux

11

Outils requis

13

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...