Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)
Woody

Créé par

Woody

13. novembre 2026NO
6
0
0
0
0

Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)

R. H. Allen's four-passenger coasting bob from The Boy Mechanic, Book 2 (1915): a 6-1/2 ft top board with four hinged seat backs, carried on two short sleds with ash runners shod in 5/8 in round iron. The rear sled rocks on a wedge and hinges to follow the ground; the front sled steers by a broom-handle post and a wheel made from a nail-keg hoop. Every size is his.
Intermédiaire
About 3 days

Consignes

1

His list of materials in centimetres

Chargement du notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"Any wood may be used for the sled, except for the runners, which should be made of ash." His list of materials: 1 top 6-1/2 ft x 16 in x 1-1/4 in; 4 runners 22 x 4 x 1 in; 4 crosspieces 16 x 3 x 1 in; 3 pieces 16 x 5 x 2 in; 1 piece 16 x 5 x 1 in; 1 shore 16 x 3 x 1 in; 4 seat backs 12 x 16 x 1 in; 1 dowel 3 ft x 1 in; 4 rods 5/8 in x 30 in; 4 eyebolts 1/2 x 6 in; 3 hinges 5 in strap; 8 hinges 3 in strap.
3

Shape and shoe the runners

Cut one ash runner to shape and use it as the pattern for the other three. Cut a groove about 1/4 in deep along the under edge to take the curve of a 5/8 in round iron rod. Bend each rod to fit in the groove, up the back of the runner and over the top at the front; flatten the ends and drill two holes in each for wood screws (a blacksmith can flatten them, he says). Screw the irons on.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Tige de ferTige de fer4 pièces
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Scie à chantournerScie à chantourner
Ciseaux à boisCiseaux à bois
Forge à charbonForge à charbon
EnclumeEnclume
Marteau de forgeronMarteau de forgeron
Étau d'établiÉtau d'établi
Chignole à mainChignole à main
CrayonCrayon
4

Build the two sleds

Notch the top edges of each pair of runners for the 16 x 3 in crosspieces, near the ends, so the crosspieces lie flush with the runner tops and the notches of each pair line up. Fit them snugly, fasten with long, slim wood screws, and stiffen each joint inside with a small metal brace.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Vis à boisVis à bois1 pièce
Équerre d'assemblageÉquerre d'assemblage8 pièces

Outils nécessaires :

Scie égoïneScie égoïne
Ciseaux à boisCiseaux à bois
Chignole à mainChignole à main
5

Make the rocking rear joint

Cut a heavy 2 x 5 in crosspiece sloping across its width, from 2 in thick at one edge to a feather edge at the other. Fix the three large strap hinges to the sloping face, and fasten the piece solidly on the rear sled's runners with its centre 8 in from their front ends. This lets the rear sled rock but not turn sideways.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Penture de ferPenture de fer3 pièces
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
Chignole à mainChignole à main
6

Mount the front sled crosspiece

Fasten the supporting crosspiece on top of the front sled's runners with its centre 11 in from their front ends.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Chignole à mainChignole à main
Mètre rubanMètre ruban
7

Brace the top board

Round both ends of the top board and plane it smooth. Underneath, fit two crosspieces, each with two 1/2 in holes bored through its width near the ends for the eyebolts: one with its centre 12 in from the rear end, the other 8 in from the front. Screw them on. Set the shore in the centre of the board, run wires over it between the eyebolts, and draw the eyebolts up until the wire is taut over the shore, so the long board cannot sag.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Piton à œilPiton à œil4 pièces
Fil de ferFil de fer1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
Vilebrequin et mècheVilebrequin et mèche
Mètre rubanMètre ruban
8

Fit the seat backs and foot rests

Round the top corners of the four backs and cut the bottom ends at a slight angle for a slant. Hinge them to the top board with the small strap hinges every 18 in, starting at the rear. Bore 1 in holes about 1 in deep in the edges of the top board every 18 in, beginning about 5 in from the front, and drive in pins 4 in long cut from the dowel, as foot rests.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
Penture de ferPenture de fer8 pièces
Goujons de bois durGoujons de bois dur1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Vilebrequin et mècheVilebrequin et mèche
Mètre rubanMètre ruban
9

Make the steering

Cut a broom handle to 18 in and fasten one end in a hole bored centrally in the 5 in crosspiece of the front sled. Bore a hole in the top board through the centre of the crosspiece underneath; put two metal washers on the stick and run it up through the hole, then fasten a hardwood collar to it just above the board so the top cannot lift off the sled. For the wheel, fasten a piece of wood across a nail-keg hoop, cover the hoop with garden hose and wrap it with twine; bore the centre of the crosspiece to fit the broom handle and screw it on.

Matériaux pour cette étape :

BalaiBalai1 pièce
Rondelle plateRondelle plate2 pièces
Planche de bois durPlanche de bois dur1 pièce
Cercle de ferCercle de fer1 pièce
Tuyau en caoutchoucTuyau en caoutchouc1 pièce
Ficelle de juteFicelle de jute1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
10

Join the sleds and fit the ropes

Fasten the rear sled to the top board with screws through the free wings of the hinges into the crosspiece. Bore holes in the front ends of all runners and attach a chain or rope: the rear one's loop to the underside of the top board, the front one for drawing the sled.

Matériaux pour cette étape :

Vis à boisVis à bois1 pièce
Chaîne en ferChaîne en fer1 pièce

Outils nécessaires :

Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
11

Troubleshooting

Bobsled troubleshooting.

Flow

Loading...
12

History and honest limits

From "Four-Passenger Coasting Bobsled" by R. H. Allen, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 24-26). The runner shape comes from his drawing, not from figures. The scan calls the steering collar a hardwood collar; the Gutenberg text drops "hardwood". The tools and metric figures are ours.

Matériaux

15

Outils requis

12

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...